Thermal Grizzly Minus Pad 8-120x20x0.5mm 2-Pack Thermal Interface Pad, Electrically Non-Conductive, High Thermal Conductivity & Compressibility for SSDs, GPUs & Electronics

Worked perfect and the thinness did the job great. Will buy if I ever need another one.

These thermal grizzly pads are awesome - high performers. They are more expensive for the size though so I bought this 120x20x1mm to apply to the high heat areas like the VRAM on the baseplate. I paired these grizzlys with a cheaper 1mm alternative with a lot more surface area to work with for the less sensitive areas and the backplate (the blue stuff in the image). The combo worked like a dream. These pads don't deform or elongate at all when removing the film, unlike the other brand I was using (AIYANNI). This made it really easy to apply and stay in place (and cut to precise rectangular areas) and just sticky enough! As far as the orientation, I would recommend FLAT side down on components and rough side upward because this will make it easier to remove baseplate in the future without tearing off pads since they will have a better adhesion to the PCB components. When it was all said and done, my card was 20 degrees C cooler!! This was at both resting and full-load. If anybody was worried about the different size of pads on this specific card, fret no more! 1mm is perfect for all areas! Just be sure to carefully cut and apply to the correct areas and components, and you're set!

Been using my 1TB WD SATA M.2 in my enclosure and the thermal pads that came with it were garbage honestly probably 0.5mm. Bought this to bring down temps. The good thing about my case was that I was able to apply some thermal pad the the top and bottom of the SSD with no problem and actually helped me screw the SSD down a lot fast so can’t complain. Excellent pricing for this SSD and the thickness is excellent for small enclosures or motherboard m.2 SSDs. With the amount they give you I was also able to apply some of the thermal pad to the enclosure controller and it fit in the enclosure with no gaps in the pad. Fixed the heating problems I was having. And was pretty durable when I had to reapply it compared to other thermal pad brands. The SSD is running at 35 degrees C while copying over 400GB of DATA to my NAS drive and my external drive.

Used this to replace factory pads on my Gigabyte Z690I Lite. Less brittle than the ThermalRight pads and dropped temperatures by 70C to 60C over the worn-out OEM pads.

Did the job so well for my ps4 slim

Worked good

Fit well and seems to work, as I modified a Mac book Neo using this pad on the main cpu to xfer heat to the bottom chassis

I have a used Dell XPS M1530 laptop that I bought several years ago and my bad, I never replaced the thermal paste and pad after receiving it. I needed a replacement thermal interface pad for the CPU, the original being Silicone based. I wanted something better. This product was easy to trim and cut to the size of the heat sink surface. It has a double sticky side, and I wasn't sure if one side was prefered to face down or not, but I don't think it matters. The gap depth was 1 MM and that is what I ordered and it fit perfect. Since this laptop started to have constant high fan output I knew it needed to be checked. There was also a dust clog on the end of the fan assembly so I took the cover off of the CPU fan (four tiny screws) and used a clean, soft paint brush to clean it. Now the laptop runs quiet.

Se pega y funciona bien.

Bought from Scorpzon trading, received freshly imported, totally geniune product, when I checked the label, found that the seller Scorpzon is the official importer for thermal grizzly products in India, came in a resealable pouch, used it for my MSI gaming Laptop to replace the factory installed thermal pads. Works as advertised, easy to stick, don't forget to remove the protective film from both side of pad before installing.

This a great product to mantain low temperatures of electronic components around CPU and GPU. It's a bit expensive but quality is good. Easy to apply due to its due to small size and good quality paste. The Functionality and performance increases when used in combination with Kryonaut. Temperature around GPU and CPU were around 80-90 Deg celcius. After application the Temp of device hovers between 40-50 at room temperature.

Buena disipación para un M.2 Samsung 970 Evo Plus

Great thermal pad