Motoparty Motorcycle Windshield Extension

I installed the Windshield Extension the night before a 200-mile ride, so it was very much a real-world test right out of the gate. The ride included sustained highway speeds with steady 20 mph winds, followed by about 20 miles of off-pavement riding on a hard-packed but noticeably bumpy road. The tilt mechanism never slipped. I ran it up for pavement and down for off-pavement, and it stayed exactly where I set it the entire time. That was honestly my biggest concern going in, and it turned out to be a non-issue. For such a small piece of plastic, it deflects a surprising amount of wind away from the helmet visor. The reduction in wind pressure and turbulence was immediately noticeable at highway speed, not so much with the 20 mph crosswinds. The photos show the extension mounted and in use during that ride. A couple of them were taken at the “Big Chief” gas station—better known as the “Four Corners Gas” stop from Season 3, Episode 4—which made for a good excuse to document the setup mid-ride. If you’re on the fence because it looks small or “too simple” to work, don’t be. This thing punches well above its weight, installs easily, almost invisible when riding and stays put even when conditions aren’t friendly.

I ride a 2017 Honda NC700X with an aftermarket Givi windscreen and head buffeting was pretty bad on the highway. I had read the extensions work really well to help with the buffeting and noise, so for $30 I thought I would give it a try. It came with stainless thumb screws that replaced the plastic ones on the tilt arms and the instructions were less than helpful on how to make the conversion, but a little work and it was done. I put it on the windscreen using the small allen screws supplied, and had to apply more force than I thought to lock it in position with the tabs on the front. Once locked, I took it out for a ride and immediately felt a difference. With a few tries at adjusting the angle, I now have it in place and feel the same amount of wind and buffeting at 75 I used to feel at 30, its a total game changer for me. It does seem to place some stress on the windscreen and the plastic parts may not hold up in the long run, but so far this has been great and I would highly recommend trying an extension if noise and buffeting are issues for you.

Came with upgraded hardware to secure arms to mounts wich I think solved the issues with failure or weakness others have had .Ive found this a fantastic product works extremely well, tested at 110 mph and zero issues. Completly solid and has eliminated any helmet buffet at hiway speed while still maintaining a nice view over the top. I honestly feel this has made the front fairing more stable making bike more stable as well. The mounts are rock solid and I can not understand how this would ever just fall off. At this price it's a no Brainer for me . I bought the smaller version 11 inch, and has worked so well i just placed an order for the bigger one 14 inch from a different company. I prefer the clear version as well because when mounted it is in the lower line of sight. Something to concider especially if riding on rougher roads helps to see what directly in front of you. Update: the one from other company came today is not the same quality at all, returning .these wind screen are not all the same accross amazon as ive read from other reviews .I didnt realize motoparty sells a larger one aswell so I ordered one from them. will follow with Update.. Update: larger deflector came and I am just as happy with the product if not more, suits my very large motorcycle better. See my review on the larger from this vendor . I'm going to try the large deflector with the non upgraded plastic hardware and see how it does. I followed the instructions about pushing in the 360 locks to secure after adjustment and I have a feeling it will hold up just fine. I will update if the fail and go back to the upgraded wingnuts.. ..

Can't say how this will work on other bikes, but it is advertised as being compatible with a BMW R1250rs. It is absolutely not. The hardware is difficult to work with, and the instructions are so minimal as to be almost worthless. I'm a good mechanic and struggled for almost an hour trying to assemble it, and when it was finished, there was no way it would ever fit on R1250rs windscreen. In fact trying to get it to fit scratched the screen. Another bogus piece of junk made in China

Out of the box this shield is a piece of garbage- the hardware is plastic and easily falls out of place, leaving you with a floppy extra tall windshield. HOWEVER, with $8 worth of hardware you can turn it into a very sturdy piece of kit that reduces wind noise and buffering significantly. You’ll need 4x of each: 10-32 x1in Thumb screws M8 flat washers #10 flat washers #10 lock washers 10-32 wing nuts. Remove the old plastic hardware by putting it in the unlocked position and then pulling out the locking mechanisms along their twisting axis. Then remove the plastic pieces they made with (just fiddle with it and you’ll figure it out). Replace the plastic hardware with the new metal hardware in this order: Thumb screw, m8 washer, #10 flat washer, #10 lockwasher, #10 wing nut. Once you’ve done this the shield should be solid as a rock! I am quite pleased with how well it works.

I have an 08 Kawasaki versys, a bike I believe this windshield is supposed to fit without issue. It took some work to make it fit. There's no instructions so everything is guess and test. That said, after about an hour, I had a very sturdy, well fitting, adjustable windscreen. I am 100% confident that it's going to stay in place, has had no issue at 80+mph, and does a good job reducing wind noise. Mine came from China, so I don't know how difficult returns would be, but a little fandangling and you can likely get it to fit on even an odd windshield like the old versys. I can't compare this windscreen to any other aftermarket screen because I've never bought one, but I am glad I bought this little guy. Does a great job and the price is fair

So I'll tell you that for the money that you pay, this is an excellent alternative to the more expensive branded ones. However, I'll also tell you that for what you pay, you shouldn't expect superb quality and build materials. Does it work well as designed to defect wind in an adjustable fashion? Yes, absolutely. I've installed it on my 16' FJR just for a little more height on the touring screen that I have and it definitely works. Was easy to install and stays put. I'll try to break it down into a list of pros and cons. Pros: -Very affordable -Easy to install -Easily adjustable -Works well at deflecting wind -Easy to see through -Has stayed put through high speeds and for more than 1000 miles already. Cons: -The first one I got was definitely off-centered and nothing I did would get it to sit on the stock screen level, that was easily remedied by contacting amazon and they sent out a replacement in a snap. -It's made from a PlexiGlass material and you'll notice it immediately when you take it out and hold it up next to your actual windscreen -The directions are included but aren't the clearest. I can see someone less mechanically inclined struggling a bit -It's 80% impossible to see through it when it gets wet, I think it's due to the fact that it's that weird plexiglass material - It gets dirty in a really strange way, like not like the windscreen so often it's harder to see through and you'll need to clean it more - I think it has some weird components or film on it because after I use my microfiber to clean it, it leaves a weird hazy film on my windscreen and it won't come off unless I let both it and the windscreen dry and then use a dry microfiber and all but scrub it out. I never had any issues with my microfiber and my windscreen until this addition. -Because of the added height, it shakes a bit a higher speeds and causes the windscreen to shake with it, this also makes it harder to see through the faster you go. -The adjustable bits seem pretty flimsy, but once locked in place it seems to stay put, for now Now down to the real question, would I buy it again or recommend it to a friend? Absolutely. If you're looking for a solution without breaking the bank, this is it. I would just advise a word of caution, but at this price point, you really shouldn't be expecting anything less. It always blows my mind how people will spend 3 dollars on an item and expect it to perform like it's $90 alternative. I give it 5 stars because it does its job very well at deflecting wind, I took off a star for all the other bits that come with it.

Okay, here's the deal. When I received the reflector, I noticed something strange about it when I tried to install it on my Electra Glide. The mounts seemed...off. And they were. There are no instructions with the unit (not that they're needed), so I looked at the photos on Amazon to compare. Sure 'nuff, the clamps were put together reversed. I guess the Chinese have a hard time understanding left from right. No big deal as it was easy to take apart and put together correctly. The next problem was the barrel screws that go into the clamps. One stripped just trying to put it in (sigh). Again, quality issue. Normally I would have sent it back at this point, but I needed it for a long cross-country trip and didn't have the time. Three screws would have to do, and it was pretty secure. The real problem was after a few hours on the road. Pieces of plastic began to fall off and I was actually afraid it was gonna come apart and hit me in the face. Pulled over and got some electrical tape to jerry rig it for the remainder of the trip. Why not give it a one-star rating? Well, in spite of the quality and McGiver-ing work I had to do, it did perform well. Made the ride much more comfortable. So, two stars it is. When I got back home, it was sent back to Amazon for refund.

très utile

Good product.

Right out of the box, the main pivot joint (close to the clamps that would attach to the original windscreen) came right out. There's a few plastic pieces in there but on examination I don't know how they expect those to hold. The company provides some thumbscrews which are meant to replace that mechanism, which shows that they must recognize there is a problem here. I attached a picture of the joint. The joint actually fell apart while I was riding, fortunately it fell on the deck of my bike and I didn't lose it on the road. EDIT: Gave it a second chance today. The part to hold the joint fell off on the road. This time it didn't land on my deck. I didn't try to find it. Will be sending it back today. Second problem was that once I had it mounted on my bike, I noticed that the top screw on one side that holds the windshield extension was completely missing. I'm not sure if it was missing when I got it and I just didn't notice, or if it fell out during installation. It doesn't appear that the fastener there is replaceable so I can't fix it. Picture is attached of the missing screw hole. The manufacturing throughout is of very uneven and questionable quality. In one spot there is a large plastic deformity that shouldn't be there (picture included). The hex screws in some have their recesses either offset from center or are extremely rounded (picture included). You may not need to replace these screws, but it speaks to poor quality. I was disappointed that the mechanism to clamp the unit to the original windscreen requires a small hex key. I assume this protects it from theft, but I know some extension designs make it possible to detach without screws, by providing either cam-operated clamps or thumbscrews. I only got to ride it for about 40 km as I was worried that the missing screw would cause the extension to break. During this time I didn't notice any improvement in wind noise or buffeting. The unit seems to cause my windscreen to vibrate a lot. Given the manufacturing issues I noted, I am not sure I would trust this unit to hold together at speed. EDIT: I went for another 30-km or so ride, using it to get to work. I find it does nothing for wind noise. I would not recommend.