Screen Protector Compatible for S10 Plus/+ Tempered Glass [Full Adhesive] [Fingerprint Sensor Compatible] [3D Glass] [Case Friendly] 9H Glass Screen Protector for Samsung Galaxy S10 Plus/+

TL;DR:Pros:- Actually glass, not film. No hole in the middle. Feels fantastic.- Lasted a lot longer than other "tempered" glass screen protectors.- Fingerprint sensor still works if you install it correctly.Cons:- If it breaks, expect to spend some time with alcohol wipes picking glued-on bits of glass screen protector off your phone.- Lengthy and complicated installation, especially compared to other types of screen protectors.There are a lot of S10 screen protectors on Amazon that are outright scams, claiming a given hardness but shattering at the slightest impact. This is not one of those. There are others that either break the fingerprint reader, feel like gross film, or have an ugly hole in the middle of the phone. This is not one of those, either. This one's actually pretty good, though installation is a convoluted chore and if it breaks, removal is difficult.I'm on my second Alinsea screen protector. The first lasted about ten months before it started to develop cracks, which is about nine months better than most protectors on Amazon that claim to be tempered glass. Despite that, my experience with it overall was pretty good - it looked and felt like it wasn't there, and it protected my screen for when I occasionally dropped my phone. I mucked up the installation of my first one, probably pressed the screen at the wrong time, and had a few tiny air bubbles; this broke the fingerprint reader, but I honestly don't really care. Gesture unlock works fine. When it did eventually start to develop cracks it didn't display a shatter pattern - just individual lines here and there. And when I finally removed it, it left very small bits behind. This is one of the few negative marks I'll give it - if and when it does break, removing it *will* leave tiny bits still glued to the screen, and these are not easy to remove.They've improved the installation process in the last year. They're now providing extra guide tools (make sure you follow the link in the provided paper instead of just googling for an instruction video!) which help, and I can confirm that this time around I have no air bubbles and that my finger print sensor actually works. But installation takes a *long* time if you're being careful and want to make sure you don't mess it up, so set aside a good half-hour or more and be sure to familiarize yourself with the instructions *before* starting, then follow along with them again during installation.Overall? I'm happy with this. It does the job, lasted a good long while, and my fingerprint sensor surprisingly still works.In my view the cons in general amount to "spend a little bit more time and have a better experience long-term." Your alternatives are a filmy protector that feels like cling wrap, a hole in your screen, a broken fingerprint sensor, a flimsy scammy piece of glass that isn't as hard as advertised, or some combination of the lot. Or you could spend 3x as much on a similar screen option that also involves a convoluted installation and is probably a little tougher. But this is definitely the best of the cheapest.

This is by far the best tempered glass screen protector I've owned for a curved-edge smartphone. I've been using tempered glass curved-edge screen protectors since the Samsung S8+...most adhered around the edges and would pop or lift off within a few weeks, or would reduce touchscreen sensitivity to the point where the touchscreen was unusable. This screen protector fit my S10+ like a glove, and it definitely does not affect touchscreen sensitivity whatsoever. It uses LOCA, liquid optically clear adhesive, (same glue Samsung uses to adhere their "gorilla" glass to the LCD), which is a urethane acrylic adhesive designed for smartphones and adhering glass to LCD's. The LOCA adhesive ensures that the glass screen protector adheres to the entire screen, not just the edges.I was very skeptical of this product at first, considering it used an adhesive that requires UV light to properly cure. However, after following the included step-by-step instructions, cleaning the screen, etc., the install went flawlessly, and I had zero problems. No bubbles at all. I was able to easily make slight adjustments to center cutout on the screen protector over the front camera properly, which is what should be used as a guide to ensure the entire screen protector is centered properly. Once the screen protector is centered over the screen, the key is to put NO pressure on it - let it rest over the adhesive (use the ENTIRE bottle), and the adhesive will automatically work its way out from center to edges, underneath the entire screen protector. Installation took about 10 minutes total. Most of that time was spent using the included UV light to cure the LOCA glue, which dries and adheres the screen protector within a few minutes. The screen protector lined up beautifully on the S10+, and it's definitely case-friendly. No problems with my Spigen Tough Armor case. There's enough of a gap around the edges to prevent the case from putting any pressure on the screen protector. I've also never seen a screen protector look so clear and flawless after installation.The only slight drawback (any tempered glass screen protector would reduce sensitivity of the fingerprint sensor) is the fingerprint sensor - you do have to use more pressure and/or keep your finger over the sensor longer to get it to work. Make sure you remove any fingerprints you might have added before installing this screen protector, or they won't work. Add new finger prints with the screen protector fully installed. The fingerprint sensor WILL work just fine, but you'll need to use some extra pressure to have them read properly. You'll find that other tempered glass screen protectors will have a hole cut out for the fingerprint sensor - this is NOT ideal because the cut-out will make it more difficult to angle your fingers in different positions during the initial fingerprint setup. I recommend avoiding any tempered glass screen protectors that have cut-out holes for the fingerprint sensor. Additionally, once the LOCA has cured underneath the tempered glass, I would not advise attempting to remove it (unless it breaks from a drop, etc.). LOCA is fairly strong and not easily removable after it cures.For all this screen protector does so well, the extra pressure for fingerprint reading is not a big deal, and certainly not a reason to pass this one up. Follow the step-by-step instructions, watch the videos Alinsea has posted on Youtube prior to attempting the installation, and make sure your screen is 100% clean/dust-free before you start. 5 stars for adhesion, clarity, ease of installation, fit, and fingerprint sensor compatibility.

This is literally the only company I've tried for screen protectors and so far it's the best. I never liked that circle in the center other company's use but this one doesn't have that.The first time around I had taken it to be professionally installed and they messed it up by smudging all the glue on the bottom corners taking up a huge side that was just air bubbles mixed with the glue.They sent a replacement 🙏 and when I installed it everything went great. I followed the video to the tea. Make sure you have something to wipe all the excess glue. Unfortunately for me since I was at a high angle I couldn't see that the screen protector was cracked slightly on the button side. Hopefully a replacement can be sent. But if not I will be buying another screen protector from this company At a later time. 👍👍

Super geniales System, was es leider nicht mehr für das S10+ zu kaufen gibt. Hat mein Handy gerettet, mehrfach! Habe das Glas heute leider endgültig zerstört - aber eben nur das Glas!

This is my second screensaver from Alinsea. They have added components to make it easier to position the screensaver which works well. Excellent result

Followed instructions carefully, glue completely filled the front facing camera hole, and the image from the camera is cloudy and unusable. Had to remove the glass. Waste of money.

Was excellent can recommend.