Mount-It! Heavy Duty Dual Arm TV Wall Mount, 40-90", 176 lbs

I needed a solution that prevented my mount from extending beyond 31 inches due to the opening above my fireplace. This mount and durability work exceptionally well! My mount consistently sits extended 31 inches out, and the TV is a Samsung OLED F series TV. So far, the crossbar and cross arms have not bent or sagged at all. I highly recommend this mount.

My townhome was built in the 90s/2000s with this awkward cubbie hole for the old school TVs. I didn't have a ton of space so I wanted to utilize it with my flat screen. This wall mount was over kill for my application, but I wanted something extremely sturdy and don't have to worry about my TV falling. Installation was pretty straight forward, I don't really understand the complaints everyone has. I did see the issue of the poor quality lag bolt, so I purchased some more from Home Depot before install. Overall Installation took me about an hour with measuring and triple checking my stud location. It definitely takes 2 people for install to hold up the heavy wall mount while you bolt it against the wall. I only utilized 2 studs, but it feels sturdy to hold a 53lb tv. This also came with a super handy template that made it a breeze to mark and drill your holes. Overall I'm pretty happy with it how far it comes out and the range it can get to maneuver.

There was nothing to dislike. Heavy duty for our very large 60" TV. We mounted it on our bedroom wall that is to to the right of the bottom of our bed. We did a remodel and didn't want to have a stationary TV. We wanted to be able to watch the TV from every angle of our room. But when you have a large TV this posed a challenge. We were skeptical at first about hanging this heavy TV by an articulating arm etc...but the mount is sturdy as can be and really does its job. We love watching Tv from our sitting area as well as from our bed or dressing room. Thanks to the ability of this mount to articulate and angle the TV. Assembling the was a one person job. Hanging our TV was a 2 person job due to size. But if our tv was smaller it could be accomplished by one person. Oh and the price was super reasonable too.

So I just bought a house built in 2003 that had a TV niche above the fireplace. I used this mount and was able to mount my 65in TV and sound bar with no problems. The length of the niche was 26-28 inches from the back wall. the mount is indeed 36 inches long. And cleared without issues. Things to note. This is a HEAVY mount you will need two people to install it. Ditch the lag screws that come with the kit if you can and go to Lowe's and get quality lag screws You need to span 2 studs not three. This thing is easily long enough to do so. Then I used two lag screws in each stud with a washer that fit the lag screws. As some have mentioned make your tilt adjustment BEFORE you mount the TV. Also adjust the level. Overall this is a very sturdy mount. I feel as if I could do pull-ups from it. It should easily support a 65-80 in tv with no issues

I just got this mount and so far I'm rather impressed. It's very sturdy, yet I can easily move the tv with one hand. Movement is smooth without feeling loose or wobbly. After the initial setup (which has issues I'll explain next), everything is tight and secure. Cable management isn't the best because everything comes up from below rather than behind, but is easy to do. You just have to be mindful not to route them in a way that could pinch them when you told the mount in. The package comes with a lot of different mounting screws for various tv VESA holes. I suggest keeping the spares in case you swap tv's at some point. I actually needed them to install my sound bar mount due to the sound bar mount not having correct screws. Now for the setup. This mount is heavy. Very heavy. You will likely need a second person to help with the initial mounting on the wall. The instructions suggest temp installing (I'm guessing, and instructions are lacking) one of the lag bolts at the center point of your mounting location to hang the mount like you would a picture frame. From there, you can screw in the other lag bolts into their locations, then remove the temp bolt and screw it into its final location. If you are fortunate to have 12" stud spacing, this may work and you could get away with installing by yourself. If you have the typical 16" stud spacing, forget it. Your only studs will be on the sides. If you drill and install the temp bolt, you will need to help support the mount yourself to prevent damaging the wall while your helper gets a couple of the other bolts in. The instructions are just a bunch of diagrams that give you a crude idea of how to install this. I also noticed the mounting template they give lists a different drill bit size than what the instruction page lists for the lag bolt pilot holes. You must drill a pilot hole, and I used the bit size listed on the template, which worked out well. If you are the kind of person that needs to be told to insert Tab A into Slot B, then the instructions may take some time to understand. If you're good at looking at reference drawings and figuring out how to adapt to your situation, it's not that hard. There's no offset measurements to help you center the mount either. If you need to install the mount in an exact position, especially when it comes to tv height, then you'll need to take measurements of everything and do your own calculations. When setting the angle of the tv, there is a thumb screw of sorts to let you lock it down by hand, but it's only one of 4 screws on the tilt hinge. Do not rely on this alone, and make sure to tighten all four points with a wrench once fully set (2 pivot points, and two slotted points). I saw where others reported using lag bolts from hardware stores, and wrong sized screws for the VESA mount. I don't know the specifics for others situations or if they changed production, but I used the lag bolts and washers that were included, and the VESA screws were sized right. So just check what you get before running out to buy unnecessary parts.

The tool list and available screws with this is silly. You need a good drill. The idea that any of this could be installed with a screw driver is nuts. Otherwise, the unit is great. The tv can be turned so it is perpendicular to the wall, this has so much range. Check the length of all your cables, you might have to order a longer HDMI cable in order to reach all the positions. The electric wire that came with our Samsung was fine but the HDMI was too short. This is by far the best TV wall mount unit we’ve had.

This thing is awesome. Very heavy duty. I was very leery and doubtful that it would support my big-ass 65' TV. I was almost shocked that it supported it just fine, even at full extension! Very adjustable in length, and TV angle (up/ down, left/ right.) Also almost unlimited holes for attachment to wall (I actually drilled a couple of extras to fit my stud arrangement.) Also, the TV brackets slide on the rails to fit almost amy TV size, with lots of holes for TV sizing.

I rent a home that was built in the early 2000's and has a built-in entertainment center with shelving in the living room. The dedicated TV opening at best fit a 40" screen, which with today's modern technology, is not big enough for the average viewing distance (7-9 feet). With a wall depth of 24", and wanting to retain space to reach movies & records in the adjacent shelving, that called for a tall order in an extended mount. This is just the product I needed! The 36" mount extends far enough to allow for me to get behind the TV for cleaning and reorganizing. Alternatively I can also push it back flush against the shelving for a more sleek look. The mount is heavy, as expected, so definitely get a second set of hands to help with installation. Overall it is fairly sturdy, although I did notice some slight "bobbing" of the TV bracket during final adjustments. I also had no problems using the included hardware and mounting it my Samsung TV and the available stud(s) in the wall.

El producto se ve robusto. Gira 90º de manera cómoda a un lado y otro. Mi TV es de 45".

You're buying this because you have a huge TV which you want to turn quite a lot! And you want it to be sturdy? Then this is the one. I saw a bunch of other options on amazon before deciding on this one which I chose based on the reviews I read. All the others had reviews about the arms bending under load or not being straight, etc. The arms are sturdy, very strong. There are plastic clip ons to pass the wires through. It does extend out very far as described, but you don't quite get a 90 degree with a 75" TV. Maybe 80 degrees would be more accurate. Not a huge deal. If you have a smaller TV, that shouldn't be an issue. When you tilt it down, the turn thing is basically same as any other TV mount. It's a cheap way to get the job done and it works but it's not fancy or accurate in any way. So I don't tilt it down often because of that. There are no markings so you can adjust to same point every time and there is no way to tell when you straighten it out if it's actually straight. It makes maneuvering around more time consuming than it needs to be. But there are no better options! In this price range at least. Look, it's expensive but it gets the job done reliably and trust me, you're better off spending a few hundred dollars on a TV mount than however much you paid for your TV if should come crashing down with a cheap mount.

El soporte se siente muy bien, pero el juego de tornillos y taquetes que trae para ponerse en la pared no son muy buenos en realidad no aguantan el peso de una tele de 75 pulgadas.

Très satisfait et j’ai une 85pouces