upHere GS05ARGB Addressable RGB Graphics Card GPU Brace Support Video Card Sag Holder/Holster Bracket,Built-in ARGB Strip,Adjustable Length and Height Support

Awesome selection! A lot of the RGB GPU supports/braces are so over the top with acrylic and the angles they look cheesy. The RGB is diffused very nicely, if I remember correctly it has 12 LEDs which really helps with less hotspots. I was nervous about the lighting and how secure it would be but holy smokes it's significantly heavier than I anticipated.Mounting was a bit of a pain but if you lay your PC on its back it makes it much easier to mount while keeping covers in place!Definitely supports my GPU (Asus Tuf 4070ti), and it looks amazing while doing it!

For $15 you can't get much better than this. Most GPU support brackets are crazy expensive. This one is pure quality for only $15. It is made of solid metal, so you don't have to worry about it not doing it's job. The RGB syncs to you motherboard, and the colors match. RGB is subtle and not obnoxious, only issue I can see is the adjustment for the amount of support doesn't really help all that much, and you're stuck guessing at how high you need it, but once it's set you're good. Sag is gone and it's a really good looking piece in any build.The only bad part is putting in the screws for the expansion slots, a magnetic long screwdriver is a must, otherwise you'll spend a lot of time trying to set the screws and then trying to screw them in.

It's perfect for the money, came with 1 dead LED but it's not a big deal you can't notice it unless you're really staring at it because of the diffuse plate. It's going to work great and keeps some weight off my PCI-e slot when my triple slot GPU is installed.Pros:Thicker than I was expecting, pretty sturdy design.Comes with long thumb screws so you can keep your PCI-e covers on, or install a smaller card behind it(e.g Wifi, NVMe Raid Card)Addressable RGB is great, syncs perfectly.Comes with Rubber pads for vibrationsNo SATA Power needed(idk what some of these other reviews are talking about)Slider can be adjusted on both an X and Y axis.Nice quality packagingCheapCons:Has one dead LED(Not really too noticeable though)RGB is a little less saturated than my RAM and Fans.Slider is a little bit stiff when moving up or over the first time.Sits slightly crooked with weight on it, like 2 degrees not a big deal, barely noticeable.

After purchasing a RTX 3080 I knew i'd need a bracket as this boy chonky. Reviews looked good for this and I liked the fact it was steel and had aRGB. Plugged it into a vacant rainbow RGB slot on my controller and off it went. The ability to move the contact point was imperative as my GPU slopes at the contact point, but was able to fit it between the fans and it is holding strong.No brainer for big GPU's, and adds some flair too.

The quality here is more than acceptable for the price, but the individual item delivered was plainly not new, and was missing the rubber pads described in other reviews. That wouldn't have been a show stopper, but the Arc 770's lower shroud is curved -- attractive, but not really compatible with the small flat platform on offer at the end of the strut here.In addition, I'm a tad skeptical of the design after an attempt to install -- in theory, the use of three slot screws should be pretty solid. But in practice there's too much play for the thing to be really stable. You really have to bear down on the screws (more than I'm comfortable with anyway), and you also have to get the thumbscrew that holds the card up just right to really prevent sag. In my case, the only place I could find that would allow the system to prop up the card was along the edge of the cut out for the fan -- not really ideal.The RGB plug on my unit was also loose and readily slid off the motherboard header -- but I suspect that was an issue with this particular unit. The lighting itself was fine.Not really a negative review -- what's here is reasonably well made. Just not a design that ended up working in my particular use case. I'm not sure the Intel card is really heavy enough to require a brace. But I may try one of the thin posts that are magnetic on the bottom and threaded on top to allow more precision about the upward pressure applied to the card, and a simpler design that is less likely to allow play. Sometimes simpler is better.

I say less conventional because I did use them as GPU supports for 2 different systems, a job they do well, easy to adjust and 3 point contact for the base BUT I took the RGB strips out and put in some cut-down strips from a set with proprietary connectors with the fan kits iinstalled in those systems. I then to those addressable strips that came with the brackets and put them in a different system as general RGB strips off to the sides. Not only do the custom jobs look great, but the strips were easy to work with and can daisy chain and look great. That's why I did not include pictures, because some people will see something that is NOT what they purchased and probably won't read this and get pissed off haha but they are great supports, great RGB and easy to open up and mod for proprietary setups

The mount is a sleek design. The ARGB can be plugged into the Phanteks P500A digital controller and ran with the rest of the case. I was curious if this was the case and very much surprised that it worked out. The material is sturdy and more than capable of holding the case up. Its not a case of "you get what you get, hope it fits", its an adjustable lift that raises and lowers on a slide, and slides along the rail for one to position the support against the video card wherever you like. All in all, I love the aesthetic am pleased with the outcome.

Most bad reviews I read stated that it doesn't fit with some cards, but that's due to incompetent builders who don't understand how to undo a screw to slide the part that touches the GPU.Super easy to install, great product that I've had for maybe two months now.Also should note that this will work with any RGB controller that I've used so far, so you don't need to have an onboard RGB header on your MOBOI only gave this a 4/5 review though because something weird happened and the RGB stopped working once a few days after installation, but once I reset the wiring it was back to working again. Will update to 5/5 if it doesn't happen again.

Me encanto, queda muy bien en mi ensamble y cumple con su función

لا يركب باي طريقه تفكر فيها حاولت بكل الطرق مافيه تناسق بين الفتحات لتركيب المساميرالافضل تشتري ستاند عامودي يوضع بدايت الكرت هذا ابعد عنه

El producto funciona a medias, permite compensar un poco el estres de la tarjeta grafica, termina sediendo al peso de la misma. Como soporte cumple a medias. Muchos se quejan del RGB pero en lo personal eso no tiene importancia para la función que debe desempeñar y es el de dar soporte a la tarjeta de video.