Cerium Oxide Glass Polishing Kit, Glass and Windshield Scratch Removal Kit, 8 Oz of Gordon Glass Cerium Oxide Polishing Powder, 3 inch Felt Polishing Buffing Wheel

I had some scratches on my windshield from my mistake of using a razor blade on the glass. It left a bunch of small scratches on the 2inx2in area. I tried buffing it out with auto polish compound it didn’t remove anything. I then tried toothpaste after reading that may work, it did not. Finally I came across this glass polish set. I tape off my car aside from a small square where the scratches were. After about 20 mins of polishing the scratches were all gone. It’s messy but works wonders! Beats paying $1000 for a new windshield. The scratches are completely gone. Very happy with the results.

First of all, I have some idea of what I'm doing, although I have never specifically buffed scraches out of glass. With ample study, I chose this product. It turned out to be the perfect choice! I had scraches in my brand new windshield from nylon packaging tabs mistakenly left on new wiper blades for one rain storm. I could just barely feel the scraches with my finger nail. I own a cheep random orbit car buffer, so used that rather than the buffing wheel that came with the kit. It works faster and with the edge, I could focus the buffing to just the narrow, arch shaped scraches. So I could see where the scraches were while buffing with the slurry, I marked them on the inside of the windshield with a wax pencil. Except for climbing up on the hood and bending over with the buffer, the process all went very well. There was about 1 hour of actual buffing to the job and another hour of setup and clean up. The nylon tabs were about 1/4" wide, leaving a bunch of fine scraches adding up to visually, a scrach 1/4" wide but not too deep. The buffing compound actually buffed the "sides" of the individual scraches, removing all the "frost", but leaving the 1/4" wide area with a very fine wavyness. To buff that out would have required the initial use of a courser diamond compound to remove a lot more glass material...and a lot more time. For the 2 hours invested, I am very happy with the results. For removing scuffs & fine scraches, this Cerium Oxide is the perfect stuff. However, to curb expectations, experience buffing, for instance on paint, is a huge benefit. Buffing scraches out of glass is not easy. Results will differ with users.

This is a professional product. It is messy to use and takes patience for it to do its thing. You can't just run it across your glass one or two times to remove water spots or blemishes. It takes time and effort. If you have a scratch you can feel with your fingernail this will not take it out. On a older car where the glass has lost its luster or has heavy water spots this stuff works fantastic but be prepared to invest 1 hr or more for just one piece of glass to see improvement.

We had brand new windows put in to our home and they showed up with scratches right in the middle of them. I bought this product to use to try to get them out and I took my time because a lot of people in the reviews said to be patient with the product and take your time. I used the drill and kept the Product wet with a spray bottle and Work the product into the scratch, and slowly but surely you would see the scratches going away and after 20 or so minutes on each window. The scratches came out. Worked for me! The scratches were deep enough that my nail could get caught into it, and about 2 inches wide and 3 inches long.

Didn't make any difference after three applications. No instructions with product. Found instructions online but pretty vague.

UPDATE: I ended up buying a new tank because this stuff was so annoying to work with.I purchased a used aquarium and didn't notice how scratched it was before I took it home. Instead of buying a whole new tank, I wanted to try to buff out some of the surfaces scratches, knowing that the deeper ones (ones that get caught by your fingernail when you run across it) are NOT coming out. I was glad that the kit came with the powder AND the buffing head plus it is Amazon's Choice so it felt like a no-brainer. The box that came in the mail with the products had NO instructions. I had to come back to the listing to see that there is still no real measurements for how to mix the cerium oxide. It says something like, "use a couple tablespoons and add enough water to make a slurry (thin, paste-like)". In reality, other sources say to NOT make a paste and that the mixture must be 2 parts water to 1 part cerium oxide powder so it is relatively watery. I had used the buffer head with the cerium oxide "paste" like the product listing told me to for over an hour and NOTHING changed. I kept the surface wet and cool so that the friction of the buffing did not heat up the glass and I applied equal pressure to make sure it was level and everything. I'm going to try again with 2 parts water, 1 part cerium oxide and with a handheld buffer instead of attaching the head to a cordless drill. It is VERY time consuming so it will kill all the cordless drill batteries for sure. I admit that it's better to try this before purchasing an entirely new tank or piece of glass/mirror, but you will be putting a lot of time into it and it is frustrating when the company does not even tell you how to properly use the product they sold you so you end up wasting time and a ton of product. Granted, I should have done my research beforehand, but it is still annoying.