Techflex1/8 Inch Flexo Clean Cut Braided Cable Sleeve - Black - 10 Feet

For years I've been taking my guitar synth rig (GR-33) to gigs which required laying four cables from the foot controller to the amp or PA. I tried wire ties - too sharp and cut my hands. I settled for taping them together with electrical tape every foot or so. I called the bundle the beast. FINALLY, I found this product. I was able to slip all four cables into it - three 1/4" hi-impedance (guitar) cables and one power connector - without taking the ends off. The product expands to 400% its size. It took a few minutes to figure out how to do this easily as the webbing acts like a Chinese finger puzzle. Once the cables were covered, I slipped 3/4" shrink tube over the ends to hold down fraying and shrank them down tight. Even when used carefully, this product DOES fray on the ends once cut. Shrink tube handles this problem perfectly and professionally. I no longer call my little bundle of cables the beast. Highly recommended.

I bought this to protect a wiring loom I put together. It contains 3 mic cables with XLR connectors.This material is a little narrow for my application. I installed it AFTER I assembled my cables. In hindsight, I should have obtained this material before I installed the XLR connectors.But, with a little patience, I was able to work this material over the completed cable, ends and all. It was a chore but I eventually got it. I love that it's tight around the cables.I basically used this in the manner of a product known as "Pedal Python". They have a great product and it's fairly priced.

I really had no idea what size to get for the number of cables I had. The 3/4" ended up being slightly small for me.What I was able to fit:3 HDMI cables1 analog audio cable1 usb cable1 power cordDidn't fit:VGA cable (the end was too big to get the sleeving around, and also sleeving capacity had been reached by the above items).It was a very tight fit and it took some work to push the cables through. I would get a much bigger sleeve next time and it would be much easier and quicker to install. Otherwise, the sleeve was of good quality and as advertised.

I purchased this to make installation of a new amp and speakers in my car more clean. My plan was to keep the factory head unit and ran the speaker outputs to the amp. Since we're talking about 4 pairs of 16-gauge wire I wanted some kind of sleeve to make the bundle easier to deal with and easier to hide. This product was easy to measure and cut, and singeing the cut end, as recommended in the included notes, worked wonderfully to prevent fraying. I bought way more length than I needed for this project but the price was right. I'd definitely buy this again.

As described

This does the job but what is disappointing is that if you cut it then it starts to unravel. When I bought it I was holping that it would be the kind that isn’t a complete circle and that closes in on itself. I’ll be in the lookout for that instead of this.

This sleeving was perfect for my audio application. I fit two power cords and three XLR cables in it without a problem, you just have to be patient feeding the cables through (read: slow). It is durable and frankly just what you would expect from braided sleeving. With the five cables I mentioned inside of it my overall length was 24 feet.Notes:Fit 2 Extension Cords and 3 XLR cables inside w/ 24' overall lengthSlow/difficult to feed cables through (the connectors on the end are hard to advance through cable).Be careful if you use heatshrink tubing to bind ends; heat gun can melt sleeving.

Good stuff. The 3/4" is currently holding a 1/4" instrument cable, an XLR mic cable, and two thinner 1/4" inch cables for foot switch controls. I also have some of the 1/2", which is nice but was a very tight squeeze for all 4 cables (although it would be fine for 4 thinner cables). End melts back to smooth with a lighter. Things look nice and it keeps cables together. A little tedious to get it through (bunch it up to expand and push, repeat over and over), but great once it is in.