Lens Adapter Compatible with Oculus Quest/RiftS/GO Black

These work just as advertised. For the quest 2 there is no need to pop anything off the lenses in the Quest. Just snap the prescription lenses into these adapters, and then snap it right over the quest 2 lenses.The instructions that came with the lens adapters were not very good, but there are plenty of YouTube videos out there showing the installation of these type of things.

My headset was pressing my glasses into my nose and causing pain whenever I played, especially if it was over one hour playtime. For $15 plus $20 for prescription lenses from Zenni this is half the cost of other headset lens adapters.When I first got the adapter, I took an old pair of lenses and dremeled them to fit. I wear bifocals, and Zenni lenses doesn't do bifocals for the 550021 lens. It worked beautifully, but I realized I didn't need the bifocal part. I ordered Zenni lenses with my single prescription and they work perfectly. Best rift s accessory I have.

These are very cheap 3d printed, likely printed with the lowest-end consumer 3d printer. There's no quality control. The lenses (zenni's that are suggested) don't correctly fit in the holders, and the holders don't properly 'snap' into the headset. Both issues are likely caused by the 'tolerance' / imperfection of the low-quality prints. Once they're attached as well as they can be, the lenses will rotate inside of the plastic pieces, especially when you clean them.All in all, this is barely more convenient or comfortable than just wearing the glasses that the lenses are removed from, which fit just fine inside the quest 2.

These are great. Fits the zenni round lenses I used in my cv1 lens holder just fine. It was kinda tough to get them to hold on and not fall off but you gotta push them on until they click. Which is why I think these are getting bad reviews because it can seem like they don't fit at first but you have to push them over the lens until they snap on.It feels great not having to wear glasses with my quest and I have no real complaints than they are a little tough to click on.

Atleast from my experience, the lenses fit in the adapters with no issues. However when I had to put it on the quest itself it just wouldn't go on. I had to eventually find that perfect angle and just firmly push from all sides of it until it finally was able to squeeze down on to it.After a month of them being on they could then be pulled of and re-seated without issue. Its the initial fitting that is rough with the risk of pressing too hard in the right place and potentially scratching your quest lenses. Get past this point and you're good to go.I also had to occasionally take the adapters off since the lenses can ever slightly turn as you clean them. I'd just pinch the lens with a microfiber cloth in my fingers and twist until they were lined up just right.Other than the initial nonsense and occasional adjustment. Its well worth having prescription lenses in the quest if you wear glasses.

Theses 3d printed adapters seem like they don't fit as securely as I might like, but that is the nature of 3d printing - there is some warpage that occurs. Despite this, they have remained securely attached to my Quest, and hold the lenses really well. They really are a great inexpensive solution, and I have no complaints as to the way they function. These are SO much better than wearing glasses - I would gladly buy them again.

Clips onto the Quest 2 lenses mostly ok (a bit loose on 1-2 tabs). Had to clean up the adapters a tiny bit from 3D-printed bits with a lighter, but took about 20 seconds and was easy. Overall, it works greats, and is a lot more affordable than the $80 some companies want for specific lenses.

If you wear glasses and want to play V.R comfortably then you must buy this. Its great and super easy to install, not noticeable once installed its a simple twist on and off and even a full twist, amazing product

Gave these to the guy that I always buy my glasses from as he told me he has made lenses for a couple Quests now.He said these took him 3 hours to inset the lenses and install on the quest and that he would never use these again.He's always used the ones that have a magnetic clip before and those take 30 minutes.So coming from him,I would not recommend these to anyone.

it is a rough 3D printed plastic. not polished. expecting more polished surfaces.does not fit well into oculus 2