BushwackerPocket/Rivet Style Color-Matched Front & Rear Fender Flares | 4-Piece Set, Bright White Clear Coat, Smooth Finish | 50915-15 | Fits 2016-2018 Ram 1500; 19-22 1500 Classic (No R/T & Rebel)

Looks nice, I had no issues with it's condition after shipping.The trim was a slight issue as others have mentioned. If I had carefully measured things out and made sure I did the exact length necessary for each fender, I would've just barely had the exact amount needed for installation. But Bushwhacker really should just include enough for installation with maybe 5ft extra so that I won't have about an 8inch stretch that I need to get more trim for. I think having 5ft extra would be more than enough for anyone to install these and they'd have a little room for error too.I haven't experienced any noise coming from the simulated bolts, but I do plan on getting taking these off and using some plastic safe epoxy, placing a drop where the nut sits against the inside of the fender as well as another drop inside the nut where the bolt threads through.Installation was more tedious than difficult, the trim could have been designed better and id have preferred that there was a flat 1inch lip inside the fender where it sits against my truck along the outer edge so that normal double sided tape would've worked for installation and it would help prevent any portions of the flares not staying flush.Only one hole per fender needed adjustment to line up with the factory screw location, meaning I needed to drill a new hole, I don't find this to be much of an issue but it would've been nice if it was an exact fit.For those that have complained that the fender wouldn't sit flush, I think you didn't follow the directions. I had one that wasn't sitting correctly so I loosened each screw, then tightened the screws and it was fine. The directions do sorta say to not tighten the screws completely until you get all of them threaded into their locations a little but they could have specified that particular issue and explained it a little better.

These look good but Bushwacker should be ashamed of the trim they provide and only a three inch margin of error in material provided. Also the rear flares were marked left and right reversed. I wound up reusing most of factory mounting hardware as the stuff provided was poor quality. Finally the holes that the screws go through had to be opened up as there was alot of material still present from manufacturing. I bought these because of the name as I have used before but in reality I didn't get what I paid for and am convinced I could have spent half for a similar quality product. This is not my first time using a Bushwacker product so I know what their quality used to be. Enough said.

Love them the rear flares were labeled incorrectly but all workout out. Holes lined up, seals were kind of a pain but overall happy with the final look.

PROS---look nice when installed....seem pretty robust so I expect they will lastCONS--1. the gasket is a joke, should be form fitted around the front ends, makes it look tacky with all the cuts needed.....kind of a hassle to deal with but by the time I got to the fronts it was okay. 2. screws are worthless, too short and they are Philips head, seriously? 3. the fenders are labeled left/right and the instruction are passenger/driver.....seriously again.....and mine were mislabeled. 4. all the drilled out holes were left sloppy with burrs, for this price they should be perfect. 5. lots of blemishes on the flares, some cleaned up but some not. 6. would I buy them again, hmmmm, I could go either way.....I didn't like having to remove the HEMI badge but so it goes, it only misses the mark by about 1/4-1/2 inch....took me about 8 hours including removing the badges.....save time by using the OEM screws, I finally wised up...

Purchased for my 2017 Rebel with side compartments....not that it matters, ordered on the 21st of Dec and arrived at noon on the 24th. So I decided to install on same day, 24 Dec, thinking it was as easy as removing factory flares and boom, install new flares and be in time Christmas Eve dinner.Anyway, missed Christmas Eve dinner. Do not be fooled that this is a direct bolt on. Fit and finish is terrible. For the front, they do not line up to the bottom of the headlights like factory. YOU WILL have to remove the front Hemi badge in order for the flare to sit correctly. The flares themselves do not sit correctly along the contour of the wheel well and if you over tighten it, you will rip/ crack the new flares....as there is a good 3/8 gap between fender and flare fastener.For the rear, 3 out of the 7 fasteners align in same hole. You will have to drill 4 new holes. Fit and finish on the rear is terrible as there are gaps between the fender and flares...not huge, but you can tell they don’t sit right.If I haven’t been committed and there was a way to reinstall the factory flares I would. I would return these in a heartbeat. Not worth the money or headache. I will say one positive thing; They do look nice and the matching paint is spot on.If you buy for a 2017 ram, be prepared and set aside 7 hours or more to install correctly as you will also have to trim the rear new flares by about 1/2 in the back side to fully align them correctly. It was starting to get dark and cold and I was out of steam.You will have to remove the rear tires to get access to drill and what not, just easier.Do not buy if you don’t plan on drilling new holes or want to remove your factory hemi badges.

Product did NOT line up with body lines (leaving gapes) and badges would have needed to be removed. I returned product to find I am now out $420 on shipping product back and getting less then what I paid for the product!I recommend finding your fender flares from a company that stands for customer service and dosent try and take your money and resell product to someone eles as new for full price! Will never do business with this seller EVER again.Nothing but a headache and loss of money

Pour deux mois et demi d’attente, j’ai été obligé de repasser la commande à 3 reprises pour enfin les avoirs, je croyais avoir le droit à un rabais

Missing install hardware Now gong show returning cause of size and have to pay ship it back. So not a good deal. Not thrilled at at all

I installed these fender flares after doing some rust repair on my 2009 Ram 1500. I love the look of them and once installed they are very sturdy. I found the install fairly easy and the directions provided were very informative.My big issues I had with these flares was I was missing a decorative washer for the decorative bolts along the edge. Bushwacker only provides just enough hardware for the flares with no extras. So when they are short by even 1 piece, you are short. I had to go out and find as close of a matching washer as I could but couldn't find an exact match. It's not terribly noticeable, but I notice it. For the price they ask for these flares I wish they would provide even 1 extra set of bolts, washers and nuts.

It looks good, just poor quality. Didn’t like the way it shrank.