Siraya Tech Fast ABS-Like 3D Printer Resin 405nm UV-Curing Non-Brittle High Precision 3D Printing Liquid Standard Photopolymer Resin for LCD DLP 3D Printing(Grey, 1kg)

Same print settings consistently fail with other resins - and of all the "ABS-like" resins, this is the one that comes closest to filling that promise. It's far less brittle than just about all its competition. It also cleans very well in IPA. Odour is there - but lower than most of the others. So - by far the easiest to print with, best quality results on successful prints, low odour, and only costs 30% more than other resins - which makes it definitely better value when you offset that premium against failed prints from other resins. [EDIT] pigment version makes a really big difference - white is a bit problematic as it suffers a lot of bleed though on the support side - seemingly due to low pigment levels. It's possible this is be due to pigment settling out, but I always shake the bottle a lot before use, so when using White I end up adding extra pigment Navy blue on the other hand is very heavily pigmented - and the pigment definitely does settle out, although is easy enough to stir back in. The extra pigment means that all details are beautifully crisp, even on the support side - it also means the cure times need to be at least 50% higher

Head and shoulders above Elegoo resins on my ageing Mars. Little smell, no print failures, less damage when removing supports, cures much faster. This stuff is amazing.

After trying a few other resins I honestly can never go back. Sirya tech fast has half the oudur which is great for a not fully sealed printing room. The quality and strength is unmatched with even thin bits of models being strong but not too brittle. And faliure rate by far the best feature for me is very low compared to other resins. Its not quite as fast as advertised but it still lets you reduce exposure about 40% on average. The cost is also only slightly higher then the competition. Easy to work with Great quality prints Low smell Low faliure rate Fast prints I wont be buying a diffrent resin for mini printing unless somthing new and incredible is realesed.

Used elegoo resin for a while and didnt think I could do much better. After dialing the exposure i have been constantly surprised by both their white and Navy Grey. The white can be a little translucent, but it prints fast and sharp. Navy grey is probably the single best resin i have used. Yes the pigment will fall out of suspension, but the resin holds detail, doesn't warp and sands amazingly well. Just take some time to stir the vat and it will be good to go. The small extra in cost for this brand is worth every penny.

First resin I've used. Comes out somewhat sticky but from what I've heard that's normal. No idea on the paintability yet. Prints fine details well, but many can be very very delicate. Doesn't smell too bad, either.

This resing gives great results i have used the gray and switched to navy gray as it shows the hilights and shadows better when selling items. Can not fault this at all. Every time I think I will use a cheaper brand I regret it instantly. Great results on mono x 6k at 2sec per layer. There is a mild smell but it is no where near as bad as the cheaper resins. Its tough once cured and if you printing minis I would recommend getting the tenacious and mixing in 100ml or 10% into the fast to get a bit more elasticity part so if the mini is dropped little parts won't shatter. The only down side is cant find the 10l bottles in the UK

Better than I expected Iv used a lot of different resin in my time 3d printing and this has to be the best I’ve ever used will definitely be buying more of this 😀

Best resin I've used to date with my Saturn 4 ultra, and there have been a few. Detail is exceptional, fail rate virtually zero and calibration settings importable from Siraya Tech website. Not as cheap as others but hugely better imo

Realmente no la compararia con ninguna, es una resina standard de la misma calidad que cuaqlquiera, el olor es similar a las de 30 euros, la calidad final igual, es quebradiza, si se te cae la pieza de la mesa se rompe, no entiendo la fama que lleva, perosnalmente no veo que sea una gran resina.

Súper buena para impresión 3d y trabajos dentales

i have a elegoo saturn and this worked very well i have had no fails using this (apart from my own packing this in to fill the build plate and supports getting stuck to other models). it barely makes a pulling noise from the fep and works fine at 28c (ive had it up to 33c in the vat with no problem) temperature as i live in Aussie and well its warm here. The detail and pigment is on point (4k screen 0.50 layer height no anti a ) and am happy with the results ill be trying in on a mono x and a 4k mini soon to see the differences in res and machines Cons ..... if you drop minis from bench (900mm) height onto tiles it will shatter (ive busted a few small minis like this ) compared to some others its a bit smelly ( i didn't think so until i had used a bunch of other resins) but still not to bad. a bit more expensive than other resins, but hey i only did one tank clean while using this stuff compared to eco and craftsman where eco was after every print (always had at least one fail) and craftsman with the occasional fail , so in that regard maybe not so expensive. these prints were done with - burnin layers 4 exp time 30 trans 0 light off 0 lift 12 speed 40 normal layer 0.05 light off 0 Exp 3 lift dis 7 150/150 lift -retract speed

J’utilise cette résine depuis 3 ans maintenant et jamais déçu! J’en ai essayé d’autres mais elle reste ma préférer, résine très fluide idéal pour l’hiver, la qualité est au top une fois bien calibré, peut d’odeur, et le prix et vraiment bon. Selon moi c’est la meilleure résine rapport qualité prix à ce jour et cela depuis 3 ans

Me ha sorprendido mucho para bien. En primer lugar, las dos resinas Siraya fast que he probado, huelen mucho menos que otras que he tenido. En cuanto a resistencia/tenacidad, no he hecho pruebas, pero en mi caso no es lo que busco. El acabado de la pieza, mate, en ese gris marino, y el nivel de detalle y resolución, son espectaculares. La figura está impresa con una Elegoo Mars 3 pro (4k) y estoy muy satisfecho con el resultado. Recomiendo 100%.