Pegatanke Epoxies (Black Epoxy)

I used this to seal pin hole leaks in a mild steel boat fuel tank Work perfectly sealed up all holes now rock-hard finish do wear gloves as it get very messy it’s difficult to mix because it’s very hard decant the green pot first then add the black pot the wood mixer that comes with it is to weak so you need to use something metal

Used this to repair an oil sump, very thick and takes quite a bit of mixing but is fairly easy to apply. So far it's doing a very good job. A new sump was not available so this was a good substitute.

Good stuff ,

Very impressed far superior than any other products. The secret is to ensure you mix this product properly as pie structures and it’s difficult to mix because it’s very hard however when done properly with metal it’s all clear and go off my concrete. Use this product to bonds carbon and plastic together as all other products failed to last. Impressive!

easy to use if you follow instructions wear gloves when using

Very, very thick, comes in two small plastic jars with a little wooden spatula. Wouldn't come out of the pots, it was so thick. What I did get out I tried to mix in a yoghurt pot and the spatula snapped trying to mix it. Totally impossible. Whole lot ended up in the bin and I used araldite instead.

I've used this to repair a motorcycle fairing - one of the captive bolts had seized and split the ABS plastic boss. I used a good blob of this resin and it's made an excellent, stronger than original repair. Faff free to use, plenty of workability and the drying time / full strength time is good. The best epoxy I've used and I've used a few over the years - only drawback is it's black and dries glossy black

I used this to repair a cast iron post that had broken away at a joint. May be I didn’t use it properly or maybe it was the weight of the leaning post but it failed to hold.

If you are trying to repair the coolant leaks on the plastic intake manifold of the P71 Crown Victoria, then look no further. Sand area before application for adhesion, then wait 24 hours to install. This product seems to have very small and thin metal particles, which you can sand afterwards, but I found it easier to apply in excess, then smooth it out, then wet your finger with water and smooth it out further before drying and curing. The final result will be as hard as a rock, and since this product is designed to be durable against coolant contact and heat, this should get some extended life out of your intake manifold. This stuff is incredible. My intake wasn't a minor repair either. I basically rebuilt the mounting surface on all 4 ports and the coolant stem. I'm going on 4 months of daily use, and no leaks yet.

Funciona bastante bien, en metal tiene buen agarre pero no en plástico, muy satisfecho con el producto.

I tried a few different epoxies and glues to put my rear view mirror back on to avoid having to get another windshield. My mechanic and the people at the local auto stores said it could not be done. Previous experience with some of the epoxy I've used in the past told me to try first. Well they seemed to be right. The glass is partially broken/shattered so this is the supposed reason why these epoxies won't work. Tried the super glue in the rear view mirror kits and two very popular epoxies and they all failed. I saw this stuff and had to try it before getting a new windshield. It worked like a charm! I love this stuff.I found so many jobs for it now. When I went to reorder I saw two other products they make. This one is black and I can attest to it being awesome. I am ordering the other two and will be back with reviews on those as well. I can't wait to buy it again.

Todo perfecto. Tuve un problema con el pedido, les escribí un correo y me contestaron al momento, solventando el problema rápidamente.

A pesar de las malas reseñas que tenía decidí comprarlo,el producto de 10.lo aplique en un tanque de gasolina plástico de moto,el producto resiste la gasolina aunque tuve que aplicar varias capas para sellarlo correctamente ya que al secar el producto encoge un poco,mientras no seca es medio elástico.recomendado para plásticos 100%