TOPGREENER PIR Motion Sensor Switch, Ambient Light Level Detector, No Neutral Required, 150W LED/CFL, 1/6 HP, Occupancy Vacancy Modes, Ground Wire Required, Single Pole, TDOS5-JM, Ivory

These worked out pretty well. The hot can go in either side into the back so somewhat easier for setup. You do need to wait a minute when restarting power for these to work. I put one in and was fixing another outlet on same circuit. Restarted power and this light did not turn on. Pressing button and movement didnt work. Cursed and went to put the cover on a different outlet nearby. Came back to look at it again and the motion light immediately turned on and worked fine. So I would recommend giving it a minute to startup when putting them in for them to work. Can see someone getting discouraged quickly when it doesnt start right off. Had same kind of delay with the second switch. Both are working fine now. Lowest delay before automatically turning off is listed on switch at 10minutes but have not timed this myself. Anyway, would recommend the switch since it works fine overall. Just a little delay before it starts working.

I just installed these motion sensor lights and they work great!. The motion detector is very sensitive and adjustable. The switches are easy to install and appear to be made very well. The price is awesome as well. I believe these switches are a good choice and I would recommend them to everyone looking to simplify entry and exit from a room where the light switch is in an inconvenient position. Now I don't need to reach over a chair to switch on a light, it comes on automatically and turns off when I leave. Worry free and well worth the money.

You cannot 'tap' the off button to turn off the attached device, and expect it to turn on automatically.I use 1 or 3 in my mechanical/storage/downstairs refrigerator room. I can choose to have it auto turn off after 15 seconds, or 5 minutes. It will not (due to hysteresis) adjust to anything in between. Since this is a long narrow room, 15 seconds is too short and it will turn off while I'm at the far end. Five minutes is a bit long, and I'd like to hit the off button as I leave. But, if I do that it won't turn on again when I later re-enter the room.2 of 3 is in my pantry. Here 15 seconds is fine. I cannot leave the sensor area until I leave the room entirely. Then it turns off 15 seconds later. Works very well in this application.3 of 3 is in a bathroom with shower and shower curtain. I set it for 5 minutes. If I'm there moving about, it's good, but won't turn off soon after I leave. I'd like to tap the off button, but then it won't turn on the next time I enter. 15 seconds isn't good because it is likely to turn off while I go to the bathroom or even shave at the mirror. And 5 minutes isn't ideal because while I'm showering, it goes off and I'm left in the dark. (Work around for that is to splash some water on the shower curtain. It sees that as movement, and the light stays on.)Again the cure would be to manually turn the light off when I'm ready to leave, but then I loose the auto-on when I re-enter.The obvious solution is to allow the sensor to turn off with a tap, and still come on when I re-enter.I bothered that they, TOPGREENER, didn't see that as a problem at least as much as I am that it doesn't work that way. WHAT WERE THEY THINKING???

I added this light switch to my office at work because I was tired of coming in and trying to make my way across the room to turn on the light. This thing works great. It’s sensitive enough that it definitely turns on the lights when someone walks in the room, the light stays on. I’ve never had it go off while I’m in the room but eventually it does turn itself off, so I don’t even have to worry about turning the light off at the end of the workday.

easy to install

Easy to install and works as it should. Great price also.

I purchased this product to replace a Leviton unit that was malfunctioning. I installed this unit in my closet and it worked fine until my wife by mistake, turned on the light manually Since then it works inconsistently Sometimes it turns on when you walk in and sometimes it does not. I have tried reprograming it to no avail.The only good news is that when the light goes on upon entry or when switched on manually, it will shut of per the time limit that I set. I don't know whether to buy a new switch or get another wife.

I purchased the two pack and successfully installed the first one in our 2nd bath. From the get go, it was going on/off randomly even when there was no motion. I reduced the sensitivity to the lowest setting and even then it continued to go on and off way too often. So I went ahead and switched to the Vacancy mode. After a couple of days switched it out for the 2nd switch to see if the product was defective or my settings were the issue. The 2nd one was much better with going on/off randomly. It still does occasionally but not continuously like the first one. Looks like one out of the two I got was defective. Amazon took care of my by giving me a credit.

Me pareció buen producto como no lo pude instalar inmediatamente hasta ahora me di cuenta que uno no funciona o sea que el 50% bien

Product works great and as it should. no real complaints. However one small jiffy, the motion sensor doesn't seem to capture anything below it, so my kid sometimes doesn't trigger it - or the one by our stairs doesn't get triggered until you're leveled with the sensor... I imagine a lot of them on the market are like that though.BIG QUESTION: had a question for the seller or anyone with the know-how, here it goes:Does anyone have any clue how to get the wall switch to trigger the same light from two different areas?Here's my dilemma, I have a turning stair case and the motion switch is installed at the top, and no switch or motion sensor at the bottom. It only triggers at the top going down. However going from bottom up nothing triggers until I reach the top landing area where the motion sensor switch is. Ideally I would like for the light to trigger on both ends since I go up and down the stairs frequently.I've tried using a mirror with mixed success. At fairly close proximity it appears to work if I angle it right. But a little further midway down the stairs and it doesn't trigger anything. Not sure whether it's cause I'm not angling it right or whether the mirror somehow diminishes the "strength" of the sensor... otherwise based on observation the sensor itself is strong enough to reach the distance I'm shooting for.My other option was to solder long wires to a separate PIR motion sensor I purchased (see image gallery). The additional PIR motion sensor is simply just that, a sensor with 4 wires coming out... not a switch. I was hoping to place this one at the bottom of the stair case, using long wires to connect it to the upper stair case Motion sensor light switch. I was thinking of soldering the wires directly to the circuit board of the motion sensor light switch (same connection points where the native sensor is already installed on the switch.) I'm assuming if I solder the same wires to the same points it'll somehow complete a circuit or trigger it the same way the native sensor would.But after taking a closer look at the circuit board, not all the connection points are labeled clearly enough where I would feel comfortable enough to go ahead with it.If anyone has any suggestions it would be appreciated! better yet, if anyone could suggest how I can get this to work that would be awesome. Wow I wrote a lot, hope this finds somebody lol.

Works as intended. I use it in the bathroom, it turns on the lights when I enter (when it detects movement). There's no light sensor, meaning it will turn on regardless of the ambiant brightness.I set the dial so it turns off automatically after 3 min.One thing to note : it doesn't seem to detect movement through glass. When in the bathtub, it doesn't see me if I stand behind the glass. I find myself raising my hand back where the glass doesn't hides me. I don't think it's a defect, it's just how the technology works.

Al inicio todo bien... las luces de la escalera encendian con el sensor y permanecian encendidas de acuerdo al tiempo que se ajuste... pero en tan solo un par de meses, las luces quedaron encendidas permanentemente... no hubo forma de apagarlas... ni manualmente... tuve que retirar estos switches y volver al convencional (manual).NO lo recomiendo.

Easy install, easy setup. Just wish they were a bit easier to program the timer.