Dragway Tools 2 Ton Load Leveler for Engine Hoist Shop Crane Cherry Picker Lift Hoist

Works as it needs to. Costs less than most of the ones I've found locally, and is of good sturdy construction. Great for pulling engines and lifting heavy equipment.

This tool worked very well for removing the engine from my late 90's Honda Accord and is priced well. It allows you to shift the weight easily, if necessary, to angle the engine to get it out and is priced well.

When I first saw this load leveler rated for 2 tons, I was a bit skeptical. Some of that is justified. I have just received this and have yet to use it, so no real weight test yet. Still, I have an ACDelco 1200 lb load leveler, and this one is certainly beefier (thicker steel and more of it) throughout the main frame portion than the ACDelco. The welds look decent. Where this leveler lacks, is the associated hardware. It truly is as the picture shows; i.e., it does not come with brackets at the end of the chains for adapting and connection to an engine or load. If you look at competing levelers, they do come with such hardware, but are rated for less (typically 1500 lbs or less). It comes with two chains. Each chain is meant to be placed throuh a hole with a notch that wedges the chain in place at the middle link. So just one chain per side. I have my doubts that each chain can support 1 ton each, since the middle link will be splitting the load. I intend to upgrade the hardware, as this is a cheap unit so not a large total expense to do so. The shackle at the top is 7/16" and is labeled with a WLL of 1.5 tons (Working Load Limit). The main frame is labeled with a sticker of 4000 lbs capacity. So the shackle is only rated for 3000 lbs, while the leveler itself is rated for 4000 lbs. I will upgrade the shackle, chains and obtain some brackets with known Working Load Ratings for peace of mind. Anyways, my engine is no where near this weight, and few others will encounter this either. But if attempting to lift a heavier load with this leveler, one should be aware of these factors, and know that you will need to buy some stronger hardware. With these cheaper load levelers and engine hoists on the market, I'll remain skeptical of their max ratings until I actually lift max loads with them. To that extent, my review is lacking. Lastly, mine came without the DragwayTools.com label. It is just solid red paint surface except the capacity rating sticker. Since I thought the DragwayTools.com label was kind of goofy, I'm happy it wasn't there.

The tool itself seems to be of pretty good quality, the welds look alright and i had no problem using it to level out a 383ci V8, with automatic transmission attached (i estimate it probably weighs around 800 lbs, as a package.) However the chains that come with it are a joke, i literally broke both of them, with a small slide hammer, when i tried to use the chains to pull dents out of my fender (i had already replaced the chains on the hoist with something a little bit bigger and stronger.) I'm pretty sure if you ever tried to lift 4000 lb with this hoist you would break the chains before it ever got off the ground.The shackle that comes with it is also a very poorly made piece of junk, the hole that the pin goes through isn't centered, leaving very thin metal on one side of the hole. the shackle is clearly stamped ".93T" meaning .93 tons, or 1,860 lbs.Bottom line, i would probably trust this to lift 1,000 lbs, but would never trust this to lift 4000.

Does a great job on SBC 350 for sure. Also used it to lift the front clip off my 1940 Studebaker Commander. Well made

It worked once when taking my engine out of my truck...the literally started falling apart when putting it back in WITH the engine hanging in the air over the engine bay! I wouldnt buy this if i were you because it couldnt handle a 500 lb hemi it CERTAINLY wont handle 4000 lbs as advertised and is tptally umsafe for use. If i could give 0 stars i would and if i cpuld get a refumd for this defectove piece of junk i would ask for that as well.

Very nice, useful and good quality item. Thank you.

I ordered this "heavy duty" load leveler for transmissions and engines. It arrived and i hooked it up. I tried the turn the crank and it was very stiff and at some points it would not move at all.The threads on the threaded rod were in bad shape. Not sure how they manufacture this but if it is China, no wonder. I disassembled it and ran a die across the threads to clean it up. It runs smoothly now. Why is everything such crap these days?