BoschTS1016 Outfeed Support Assembly

It shipped super fast and installed on my 4100 really easy. It fills that void between small work the saw can handle on its own and large work you need a roller stand for. Immediately put it to use on ripping butcher block bench tops and was not disappointed how it handled the heavy loads. Your saw is missing this and it is worth the investment.The only drawback is the dinky detent knob….seriously Bosch?

Good quality. Works perfectly

No real complaints about the item. Installed easily and serves the intended purpose well. But really, hard to grasp why this wasn't included with the saw/more integrated. It's such a simple and obvious assembly.Also surprising how many parts it comes with that aren't needed for a particular saw. Seems wasteful.It does add a fair amount of weight so with this plus the left side support, your portable saw starts to weigh a pretty substantial amount so consider that if you lift your saw into a pickup bed or similar.

like its sister the left side support, this rear support suffers from poor engineering. the socket head bolts on the left side are nearly impossible to tighten unless you shorten the small leg of the hex wrench by grinding it down. again, the tube for the strut support obscures the easy access to the bolt by a normal hex wrench. kudos for providing a hex wrench that i didn't mind sacrificing to complete the installation. perhaps you could provide an articulated hex wrench to actually reach these hex bolts? Grrr.

When I installed this initially, which is not trivial with fat hands like mine, I was disappointed. The support was about 1/8” below the plane of the table top. So I shimmed with washers. Pain in the neck. Then I bought the left side support. It came with elongated holes in the support, which makes it easy to align. Bingo! I realized that all I had to do was elongate the holes on the outfeed support, and voila. Perfect. I love it now.It does seem wasteful that they include two full sets for 2 different saws. I can see their thought process, however. It is better that it is available than find out that the 4000 saw outfeed support is no longer made.

Why does Bosch send outfeed supports for 2 different saws? I have a Bosch 4100 table saw, for which I ordered an outfeed support. But I received the 4100 unit along with a second one for a GTS1041A. I have absolutely no use for the GTS support and I'm not happy that I paid an extra 15 or 20 bucks for this nice piece of machined steel that's basically junk. It's not a fluke because the directions clearly show both.Three stars for value.

This is for 4100 and GTS. You can apply what I did for either one.I made table extension out of rail replacement parts, plywood and some other parts. Nothing fancy. When you buy this back extension it will come with almost two sets. One for 4100 and other for GTS. except slide bars. I used extras to extend "extension" to accommodate my ""extension"" on the left side of the table. All you need is to drill two holes (Your choice of offset) in extra support and you are done. It is like everything from Bosch. Brick house and good R&D. Have fun!

Bolts on, instructions inconsistent (6x bolts same size listed while I received 2 that were half an inch shorter.) bolts are far from being in an ideal location to install.The amount of slop in the slides is disappointing, I used a crush washer on the far bolt to bring up the end while extended.The inclusion of parts for a separate saw is just plain wasteful and lazy for Bosch to not have a separate kit option.Some rust on surfaces is a bit concerning for a new product.Tbd performance but once calibrated I think it will be a big help. This should have just been included as part of the saw...

Excelente producto

This outfeed support bolted right on to my Bosch 4100 table saw. It works great and makes handling larger material a lot easier. Excellent quality.

After waiting a bit for news from Bosch I received a new box containing the rear outfield support. No mail, no message, just a box near my front door.This time the content was correct with two plates to fit either my 4100 model or the 1040 model. Of course, as previously, there where also two trunnions for each plates so that half of the parts contained in the box will be stored to gather dust since I don't need them on my saw.I give only 4 stars because of that last point. Otherwise it would be 5 stars. The outfield support as well as the left support, that I also added to my saw, work correctly and do not interfere with other accessories nor with the gravity rise support. Some bolts are difficult to put in place for the right trunion but I succeeded. I also discovered that the rods diameter seems larger than the one on the outfield support that I had installed on my former 4000 model.My only suggestion to Bosch is to offer this accessory for only one saw model, thus avoiding material waste and higher price for the customer.

Fairly easy to install on my Bosch 4100-10 saw. Doesn't add too much weight. Comes in very handy when cutting long pieces.

This Bosch outfeed fence fit and worked perfectly on my table saw. Highly recommended.