Valve Core Remover Tool with 20 Valve Cores, 10 Brass Nuts

I don't know if I really needed this when servicing my mini-split or if I could've just lived with the valve core installed, but it seemed like it would be a good idea to have that option, and this tool wasn't very expensive at $18. It is a much better deal at about 1/4 the price of the name-brand version everyone recommends. Installation and usage was pretty straightforward. The seals all worked well and held. It was able to remove the valve core, though I did have to unscrew the heatpump from the pad and jack it up a bit to have room to pull the plunger out. The shutoff valve worked without leaking. The spare caps came in handy for my gauge set. The valve core went back in easily too. Overall, it did its job and the price was reasonable, so 5 stars from me.

Seems very well made. I expect that it will last a long time at my infrequent use. I just used it for my first time. I wasn't expecting the amount of pressure the "piston" generates when the valve is removed. Also it took about 5 tries to get the old stem out of the tool. New valve went in fine.

SO i was a HVAC tech for over 5 yrs in the 90's and never used a valve stem replacement tool by self.. On my home system i have or now had 4 leaking king valves on the HP units outside. I had watch a video on how to use the tool which was good but not expectually my experience. Make the first one on the easy to access did unlike what I did.. When you screw the tool on the port dont get it so tight.. if you get a slight leak it not a big deal.. When you open the valve and push the rod into the port be slow and you might need to twist it as well to make it through.. (hold the tool up take the rod out to see the chamber you are sliding stuff through to know what you are feeling before hooking it up.. ) When you start to remove the old stem make sure to gently push the tool on to the valve so it attached to stem,, as you start to unscrew stem the pressure will try to push the rod out of your hand so keep slight pressure on the end while you are unscrewing the stem.. keep turning till you feel it click which mean it out of the treads on king valve. now gently start to guide the extrector back with old stem, no need to pull as the pressure is pushing you back, making sure to be easy when you get started and twisting can help it through the bore.. On the first one when i pulled the rod back and tried to shut off valve on tool it would not turn as the stem was sorta in the way.. you back push back in to see if you can catch the stem to pull it back past the valve to shut off pressure. I was able to push the stem toward unit enough when i pulled rod back without stem but was able to close the valve on tool.. I removed rod by unscrewing the end and would quickly open the valve shooting the old stem out and then shut it off.. (make to be out of the way and it come with force. ) put new stem in the tool , place back in bore and screw down the nut, open the tool valve and push the stem back in.. keep pressure on knob on rod as the pressure is pushing you back the whole time. when you get it to king valve hold finger on know to keep in in place and slowly turn to tighten the stem back in.. get it snug but not over tight.. they will stip out and you are SCREWED. I then pull rod back through bore and turn valve off.. unscrew the rod and then slowly crack tool valve to release pressure can conform the stem is sealed.. you will hear a slight purge then it done. anymore and you need to redo the stem. go slow and feel everything and try to not screw it up.. Wish i had a video to share but that a lot of work by yourself and needing both hands. hope this helps.. it saved me hundreds to get this done by HVAC repair company.. all they want to do now days is replace older stuff. these unit are 1991 HP but converted to straight AC in 96 and we dont keep it 70 in summer in NC.. so not a lot of hours.. and its R-22 which is still have a couple tanks of from past business.. yes EPA certified tech.. :)

I won't repeat a lot of the other good advice here (inspect the tool closely to see how it is made, practice with it, know exactly what process you are going to use when you use it for real, don't over-tighten any of the fittings, etc). The fact is, I was about to give up on my first valve core replacement (and just use the nice new brass caps with o-ring as the seal). The problem is, with my early 2000s Goodman compressor unit, the part of the valve core that the tool interacts with was much narrower than the tool is designed for (or the included valve cores). So I could unscrew the core, but the tool did not come close to 'grabbing' it when I tried removing it. The core would stay behind somewhere in the tool. I tried bending the 'prongs' at the end of the tool inward a good amount, but it was still not enough for these valve cores.... Anyway to make this shorter, when you get the tool, take the rod/plunger out entirely and look into the bore of the body of the tool. If it is like mine, there is a stepped constriction at the ball valve. The bore becomes smaller by a fraction of an inch, with no smooth transition. So the valve core will easily snag on this 'step' and stay behind (while you pull the plunger out the rest of the way without the core). This is a huge oversight / design defect. I suppose you could consider drilling out the valve area to match the rest of the bore size to remove that step... What I did was just be persistent, and try many times (slowly draw plunger back while continually slowly turning it to maintain friction on the valve core) until I got it. Most important, I figured out a good way to 'test' if I got the valve core (rather than left it hung up somewhere). Once you pull the plunger all the way out as far as you can, shut the valve, then push the plunger forward. IF you have the valve core on the end of the plunger, you will only be able to push it the slightest bit forward (because the valve core takes up almost all of the space before the valve). You will immediately feel it hit the valve. In that case, you got the valve core and can open the end of the tool and remove it. On the other hand, if the plunger moves back a half inch or so before hitting the valve, then you know you did not get the valve core and will have to open the valve and try again. This way you don't repeatedly waste a bit of refrigerant by opening the end every time to look to see if you got the valve core or not. I was finally able to get the first one done after understanding these things, and the second was a bit easier because I knew what I was dealing with (and that it was possible). I appreciate the nice brass caps with o-rings and the new valve cores that came with the tool (hopefully they will work well).

Most leaky mini splits I've seen are bad valves. You can spot it by the compressor oil leaking out into the Schrader valve cap. This tool lets you replace a core without having to empty the system. It may take a couple trys the first time but the tool is pretty simple to use. Just make sure you don't crank down the fittings so hard that the orings expand to the point that you can't get the core through them. Take your time and it'll help you fix your system without costing you a fortune.

Great works as it supposed to!! Had a seeping leak schrader valve. Didn’t have to evacuate the entire system

I purchased a very similar (almost identical one) like this a few week prior to this one. That one has either the stem shorter (I doubt it) or the value body assembly just slight larger (longer) so when I attached the 1/4 to 5/16 adapter included, the stem cannot touch the valve core so it will not work for 5/16 connection. Unfortunately, I throw all the packing material away so even within 30 days, I could not return it. Then, I found this one and after comparing the pictures, I was convinced that this one has a "longer" stem. Upon receiving it, I checked it and it indeed works for both 1/4 and 5/16 connection, which is what it supposed to. So, now I have one for 1/4 and another for both 1/4 and 5/16. Given the cheap price, I would not expect it would be leak free forever. But, I probably would need to use it less than 10 times so it is safe (especially, I now have two). Lessons learnt, don't throw away packaging before 30 day mark....

Very well built. Does not feel cheep or flimsy. Used it on some 410 systems with out any refrigerant loss. It really grabs the Shrader cores firmly.

Excelente calidad del material, cuenta con adaptador 5/16" para R410a.

Awesome, worked perfect. lifesaver. arrived the next day. there are lots of 1/4 valve caps. Would be nice if it was half 1/4" and half 5/16th " caps. lots of people probably need this tool for mini splits.

This isolated valve did as it said. I could remove Schrader valve, replace and charge my a/c unit.

Excellent quality

The price and quality are good