MBRP S5527409 T409 Stainless Center Section Straight Pipe — Post-Catalyst

Nice exhaust for deleting your jeep jl muffler. Easy to install and sounds good on the jeep.

Perfect Fitment, Really easy to install, Takes about 2min to install, Stock exhaust takes the longest to remove. Made out of good material, Great price for an awesome looking product, Sounds amazing! Exhaust is on the louder side over moderate. It’s perfect!

There is no high pitch drone it's a mellow sound. The product is made of quality material the welds and all provided is of quality material installation is very simple you will need some PB Blaster to spray on your factory Muffler clamp make sure you apply when the vehicle is cold saturate let it sit for about an hour and then start your vehicle to let it run for roughly 5 minutes to burn off any added rust and PB Blaster and then make sure you let it cool for an appropriate amount of time for you for working on your exhaust that being said it took me roughly 30 minutes to remove my muffler and install the new pipe... what I recommend is removing the passenger and driver side hangers and by that I mean undoing the bolts that Bolt the hangers to the frame and after that remove the muffler clamp that attaches the factory Muffler to your factory exhaust pipe I also recommend using a ratchet instead of a impact whereas you can apply a better force of torque without damaging or snapping the factory clamp..

Got this for my 2020 Jeep 2 Door and it sounds amazing! Great product for a great price, definitely recommend this for anybody wanting to get a nice sound out of their jeep!

Fits as it should. Opens up around 6" of clearance in the back. Sounds good. Doesn't drone much @ 70mph with a manual transmission. Probably even less drone with an 8 speed automatic. Overall, quite happy with it.

Fairly simple install, just unbolt the muffler, brackets and hangers. Then you will have to loosen the pipe. You will have to wiggle it out quite a bit. It takes a little bit of time, just twisting the muffler to wiggle it out of the pipe, but it will come out. I did this on a stock Jeep Rubicon 4xE. After you get the muffler out, then you put the driver's side hanger. The new pipe, then wiggle it back on and bolt that hangar in. Once you have the pipe orientated where you want, then you tighten the pipe bolt. I have the 2L turbo engine, this pipe did not make this engine when it's running loud with the top off.I could still barely hear it. So if you are looking to make your exhaust louder significantly, you may have to straight pipe it. The two liter engine turbo doesn't seem to put out a lot of noise. But this will save you some weight, and you won't have a muffler.That'll smash on the rocks if you are off-roading.

Don't even bother with this product. The sound it puts out is atrocious. If you do decide to give it a try, make sure you don't damage the muffler because you will be putting it back on. I contacted MBRP directly and basically asked if they would help me upgrade to something better and was told "if you don't like the sound, too bad". It will drone; sounds like trash at startup and you won't see any mpg or hp gain (I didn't expect to it but it would"be been a saving grace". Now I feel like I'm showing up to prom with the girl who nobody wanted to go with and riding a moped. Not cool. Update: attached a picture of what it looks like a month after being installed

Good fitment and easy to install. Hardest part was removing oem muffler. Lol. Love the extra clearance for offloading

Easy install and sounds good. The only issue is the OEM bolt/clamp was rusted and needed to be sprayed with some PB Blaster a few times over a couple of days until I could hit it hard enough to break it free. Then wiggle until you can’t wiggle anymore and the stock muffler falls right off. The actual installation of this pipe is literally 10-15 minutes once the OEM muffler is out of there. Sounds good, not too loud but loud enough. I have yet to take it on the highway or off-road, but it’s fine around town. Easy “cheap” mod. I painted it with “high heat” enamel paint and baked it on following the instructions that the paint came with. Hopefully it won’t corrode as others have stated. I guess if it was a higher grade of stainless steel it wouldn’t corrode as easily but it would cost substantially more, trade off for affordability. Still a 5 star for me.

Shipping was super fast,once stock muffler comes off install is easy and perfect fit! Very pleased with cold start sound and in town driving,highway it's perfect as it's not much louder then stock,so no annoying racket traveling, very pleased

Just buy it

Getting the stock muffler out was a pain, but thia made up for that with the ease of installation. It's definitely louder, wouldn't say it sounds any better or worse, just louder. There's a bit of drone at highway speeds, but that's also compounded by the noise of 35" mud tires and Wranglers not being known for their sound deadening haha After about 2000km, installed in the fall and now half way or so through winter, it's starting to get a lot of surface rust. I'd suggest spraying it with some high temp paint or rust inhibitor (VHT or Tremclad) before install.

Parfait pour faire ronronner le p'tit 3.6