Suction Cup Mount Car Windshield Mounts Compatible with GoPro

I was using it as a mount inside the cockpit of my plane. Works fine.

Let me share my review of the Sametop Suction Cup Mount, which is compatible with various types of action cameras. The first thing I want to highlight is its compact design, which is easy to install, detach, and assemble. The suction cup mount with an adjustable arm makes placing it in various positions easy. I tested it on the windshield, the rearview mirror, or outside on top of the car hood. The suction cup adheres strongly, securing the camera while the car is in motion. This versatility gives you the power to capture your adventures from any angle. The materials used are of good quality, strong, and durable. In conclusion, the Sametop Suction Cup Mount met and exceeded my expectations. Despite its incredibly affordable price of only $9.99, it covered my primary need: having my action camera ready for the next adventure. This product offers great value for money, and I rate it five stars.

I feel like the people that complain about this not actually holding suction are just using it incorrectly. I have tested this on multiple flat surfaces and it holds suction nice and firmly. I bought this to attach my DJI Osmo Action 4 to the inside of the windshield on my car to use as a dash cam and it works flawlessly. I've also tested it out on the hood of my car and other flat surfaces and it stays planted. I am knocked it down one star because even when you tighten down all the knobs all the way, it still allows for side to side movement on the joint closest to the camera mount.

Works very well. I'm a pilot and I attache it to my single engine plane. After several flights, I still have the camera with me.

For those having problems with trying to make this mount stick. I purchased two of these mounts, and had problems with them not attaching to the windshield. I looked at the design, and found out that not enough pressure was applied to the suction cup to push all the air out to make the mount stick to the windshield. So, what I did was unroll 4 cotton balls, and wrapped it around inside the base (note photo). I felt some tension now when I close the lever to secure the mount in which created more suction pressure. Now these mounts stick like glue especially when I’m using the mount on dirty windshields at work… You’re welcome.

This camera mount stuck well on a windshield on a "102F" day. Did not come off once with the cell phone on it and I went down a dirt road for quite a while and a little bit of '4x4ing" and I mean just a little bit. So at the moment with this FIRST TRY I will say if people are saying this fell of the Inside the WINDSHEILD I would think they did not take off the protective film on the suction cup before applying. it will stick surprisingly well at first even with the protective film left on, but I would NOT expect it to last...) TIP !!! BEFORE YOU ATACH A SUCTION CUP MOUNT TO YOUR WINDSHELD, LET THE MOUNT SIT ON YOUR DASH BOARD A LITTLE WHILE TO WARM UP. (MAYBE move your car in to the sun while ding this) THEN ATTACH THE SUCTION CUP TO THE WINDSHEILD WHEN EVERYTHING IS WARMED UP AND THE "SAME TEMPERATURE" . I DID THIS IT AND they NEVER CAME OFF ON ITS OWN! IFI YOU PUT THE MOUNT ON WHILE IT IS COLD OR COOLER THAN THE WINDSHIELD and/or outside air temp. then the AIR POCKET in between the suction cup and the windshield IS GOING TO HEAT UP AND EXPAND. AND THAT JUST MAY WELL "POP OFF" THE MOUNT FROM THE WINDSHIELD. When people say their suction mounts wont stay on the windshield I think that IS THE PROBLEM. or they have not removed the protective film from the suction cup,(if it has one) or maybe their windsheild is Very dirty! :-)) Or they did not use "the suction lever, properly" NO problems with it coming off. BUT it has a Quick realease buckle mount for the camera mount. Which is Nice In Theory. But it reality is "joint" is not snug enough when buckled in. (and probably can Not be made snug enough without modifying?) So it ratlles around a little bit which could allow for some "Jiter" in the video. I think the cameres microphone also picks up the clacking noise of the buckle being loose in the mount. I don't know if this can be fixes by wedging some kind of material in that small gap between the bucke or not. Kind of a tight space. The swing arm could also use a bit more lenght and the ability to swivel around would be good. But other than that it seems to be sturdy and not fall off the windshield with a cell phone on it. But this was the first test use of it so I don't know how well the suction cup will hold up with use. But dang that little bit of rattling and noise... If I can't stabalize it I might not be able to use it. I'm thinking this is where some NOISE on the video may have been coming from. (tried a different mount earlier in the day) ALSO WHEN TAKING VIDEO with CELL PHONE. for Stability YOU HAVE TO MOUNT IT VERTICALLY with the "weight hanging down" and even better with the top of the phone braced against/lightly touching the windsheild. If you try to mount a phone "horizontally" the extra "side to side weight" and "torque" will cause the camera/phone to shake and wobble. making the video "useless"/VERY ANNOYING to try and watch. Again I think much of the wobble/shake is coming from the slack in the quick release buckle mount.... I have not tried it with an Action Cam. But I think the Lighter weight, the narrow width, would have/cause/be affected by less shake. MIGHT not be an issue? Or it could be? ... I did just try putting a rubber washer between the buckle prongs and the mounting plate it did Noticible Reduce that rattle/rocking and noise, but is it a structurally sound thing to do? I also just put a sheet of the "thin" foam antislip mesh material put in drawers and such. I put it inbetween the 2 buckle pieces and slid them together. It also noticibly reduced the rattle and squeek/clunking noise. but is it Enough? And will the material compress down? I don't know. But no problem holding on a full size, not light, cell phone mounted vertically, and removing and remounting phone from bracket MULTIPLE times while testing phones video and the mounting brackets equipment " all day long" (the first bracket I tried that cost more and seemed better more solid... Its swivel ball mount "quickly" crumbled to pieces.) But I've only tried using these brakets one time... THE ARM ON THIS NEEDS TO BE LONGER TO DO what I want it to do Properly! Now IF YOU JUST WANT TO MOUNT THIS SO YOU LOOK AT YOUR PHONE SCREEN. And don't care about taking video. (or maybe if your phone was shorter than mine or had the buttons in a better place) None of this arm length or little bit of rattle from the quick realease buckle will bother you. You would be good to go to mount a phone to you windshield with this so you can see the screen while driving. I guess for Looking at "Map Directions"? Other wise quite looking at the phone! Your Driving! IF THE ARM WAS LONGER (or maybe pushed out further away from the mounting base/suction cup so it extended further into the car away from the windshield. THEN IT WOULD WORK GOOD FOR ME SHOOTING VIDEO ON A CELL PHONE. Any body know of one like that?

Mount works well, stays in place, not very heavy. Definitely a great option and design for what I use it for!

An excellent alternative to the far more expensive GoPro model. At first I will admit this mount didn't give me a good first impression when it came to feel and quality of construction after handling a GoPro branded suction mount. However, for $10 vs $40 I was willing to give it a try. Glad I did. The suction cup holds very firmly and I have no worries about it failing when properly installed. The plastic felt like it could be weak initially, really though it seems fine. I will say that the knobs that tighten the articulating points do feel as though they could be fragile IF you were to really crank down on them more than common sense would tell you to do. If you want a suction cup mount and don't want to fork over the money for the GoPro branded mount, I feel confident in this product.

This holder is very good, value for money, makes my vlogging work easy. Never shakes, never falls down even in pitter patter roads..peace of mind.. Beware, there might be marks when held to windshield.

We tried to use this in our vehicle and it wouldn't maintain suction. It kept falling every few minutes. Super thankful my husband didn't try it on his motorbike first!

Well constructed, easy to use.

Ça va

La ventosa se suelta cuando menos te lo esperas y los plásticos se van rompiendo cada día un poco más. En poco tiempo acabó en la basura.