Sewell Ghost Wire Terminal Block, 14, 16, and 18 AWG, 4 Pack

Works great with the Ghost Wire and easy to install. The only way to make it better is to have connections at 90 degrees instead of just 180 or straight.

I read the reviews.. i figured that some people didn't read the description, and I was right. These worked exactly as described. Are they big? Yes, because they are designed for the big flat wire.. Do they work? YES. Do they hide behind my speakers? YES. Worth the money? YES. Don't skimp.. you already purchased expensive flat wire... now purchase the connectors.

Needs re-engineering. Ghost cable works well and terminal blocks look like they will mate well. However, the connection is made with two tiny screws. Two (of three) speakers sounded great, but the third had a very weak signal. Unfortunately I had already patched and spackled the wall. I am removing the wire and starting over. Solution - redesign the block so the connector clamps to the cable. I am grinding down a single edged razor blade to make a surface to clamp the connector to the cable. A lot of work, but I want a permanent installation. Update: Don’t use razor blade, it breaks under pressure. The aluminum back works perfectly and can be cut to size with wire cutters. Cut off both ends and blade removes easily. Provides a secure connection to the ghost wire. Another suggestion... Don’t make turns unless you use electrical tape. I changed my wiring plan and went diagonal, making connections behind the speakers and behind the AV console, wiring is almost invisible.

I have used Ghost Wire 2.0 and Sewell terminals in the remodel of my movie room, and now, you can't see (or trip on) any of the wires that go to the speakers anymore. Great system, but I wish the connectors were a bit more affordable.

I would not consider using GhostWire without these terminal blocks unless I was soldering my own solution. If you are not buying a pack of these with your GhostWire - and you don't have any skill in soldering/electronics, then you are making a mistake and you will not have a good experience. They are simple to use, four precision flathead screws hold the wire in place. Be sure to strip back a wee bit extra GhostWire and fold it over on itself (stick side in) so you get a slightly thicker contact surface for the screw to hold. Just watch some videos and read Sewell's own documentation on the product and you should have a great time. I see a lot of reviews complaining that this is bulky, and I don't really understand. Of course I planned my installation out ahead of time so that both terminations would be reasonably hidden, and I kept some of the non-sticky surface I stripped back to place back over the block to sort of hide it. In all I would say this is about as thick as your average modern smartphone at most, and no wider than the GhostWire you are pairing it with.

I'm struggling with my thoughts on this product. The wire itself is great, I ran it along the baseboard and even before painting it's almost invisible. But these terminal blocks are just ugly. They aren't adhesive, nor do they mount flush to the wall. So you end up with a flat wire, and then this ugly block hanging off the wall pulling the wire with it. While it works great in my use case (behind the couch), I can't help but think there must be a more elegant solution.

This is a really nice product. I used it to bring power to a led light fixture which was several feet away. The product worked as described. It was much easier than trying to snake a wire through the wall.

Defective. They all have the screws closed and so tight that you cannot open these terminals. If you try to turn them real hard with a precision screw driver, the internal screws strip. This is junk. A completely shoddily made and overpriced item. It makes the ghostwire wire that I bought totally useless.

Fit for purpose.

I ordered an eight pack of a two terminal connector but the supply was for a single piece of a four terminal connector.

The connection to the flat wire is two tiny little screws, and on the other side to the cable is still this sloppy screw connection. You need a plate that the screws press down against an alternate flat surface. These are horrible. I'm going to return them and solder instead. Unbelievable for the price!

So i bought these to go along with the 4 channel flat wire. I intended to do red-black-red-black but what a surprise while the entrance of the flat wire is for the 4 channels, the output is only 2? so this is unusable for me! for me these do not come from the same channel, i have rear left and surround left, rear right and surround right. all different channels. Cannot take these different channels and have only one output. very disappointed. is there something I don't understand in how these are intended to work?