Pro-Line Racing Extended Front and Rear Body MountsSLH 4x4 PRO608700 Electric Car/Truck Option Parts

Fits perfectly on my slash and doesn't feel flimsy or like it'd break easily!

The BEST adjustable mount set I have found bare none. I wanted to be able to put my p4de (stampede 4x4) tires on my slash and run them with out rubbing of the tires and without having to trim the stock body. Well this right here is the solution. Allows you to raise the body way up or down depending to allow a multitude of bodies to work on the slash 4x4. Im fairly certain these will work to mount up rally bodies as well. Rear posts are crazy long. Also the fact that the caps thread on!, NO MORE BODY CLIPS. I love it. Makes the body swap quick and painless for my 7 y/0 just paint the caps a bright color so if u drop one you can find it. Don't even hesitate these mounts rock. Pro-line is stand up company with solid products and support.

I like these body mounts. Got them to put 2.8 sand paws tires on my Slash 4x4. Only thing I dislike is that they can't be adjusted closer or further away from midline (factory mounts have 2 positions for wider and narrower to accommodate different shells. I also had to cut mine because they were too long and would hit the controller arms when the shocks fully compress- the mounts aren't to blame here....

They do the job but i wish the front also had a horizontal bar to make the mounting posts more rigid. Right now they are flimsy and move easily when testing for durability. I also advise to still use the white plastic washers even with the screw down posts if you are bashing.

I'm new to RC trucks, but when I bought the Slash, I thought the body height was way to low for my liking. Also have heard of people saying the inside of the body rubs on the plastic nerd bars on the side of the frame , as well as tires rubbing in the inside of the wheel wells (because of the body being too low). What I did, and I think it was very useful, was put the extenders on and stick toothpicks inside the holes (perfect fit) to allow you to place body on the mounts and adjust the extender arms as needed for the perfect height. Also, the pins that screw into the top of the mounts where the caps screw down, need to have a good 1/8 of an inch left sticking out the the top (don't screw in all the way); as this allows you to screw the caps on tightly. Also, the kit comes with 4 small rubber washers that go over the pins, which helps the caps maintain a tight fit while crashing around. The arms are flexible as they should be, and you wouldn't want some super ridged body mounts anyways, as they would just snap off after one good hit. I found that the rear arms are rather long for the Slash, so after final setup I cut the overhang with a handsaw so they wouldn't interfere with the rear A arms and suspension movement. Overall I like this kit, and if you want to raise or lower the body on your RC car, I think it's a viable option.

Works well and hasn't broke yet

Now, I know these were meant for a slash, but I saw them and thought, I wonder if I can make these work on my cc-01. So I looked high and low for some stock parts for the cc-01 so I could run some of my other bodies on this rig and I could not get any any where. It seemed like no one had any. So I got these to see if I could mod them to work. And it wasn't to tough to figure something out. Basically put them together and then drilled a hole up through the bottom of these and they lined up with the mounting holes on the cc01 chassis. I did have to trim about 3/4 of an inch off of the bottom of both to get the body to sit the way I wanted but it worked out great. Hope this helps out anyone looking to try out something different.

I bought these to replace the crummy pins that I keep losing from my Slash 4x4. These screw on tightly and add much more rigidity to the body over the pins alone. The added benefit is that they are flexible as all get out. I opted for the extended mounts in hopes of buying one of the Dakar bodies down the road. I love the screw on nuts but I'm sure I'm going to lose one. They are very black and roll like the dickens. I'd like to see a swivel cap on them and a lanyard to secure them to the car somehow. Overall I'm very happy and would/will buy them again.

Perfect! Fits the Traxxas Slash no problem. Needed to put my 2.8 proline sand paws on. Great product. Need to be careful you don't thread the screw through the post when setting your height.

hat super geklappt. Kann man empfehlen

Still on the same set i bought but have broken like 8 bodies and the proline hasn't changed

Best thing since sliced bread !!!

Fed up with OEM pin mount body system. The nuts used with this are far superior and easier. Also allows mounting the body higher than original, which I like.