Minwax Water-Based Wipe-On Polyurethane, Satin, 1 Pint

Beautiful shine without streaks and dry bubbles. I love it! Application is easy. Shake well, I used an applicator sponge.

This is my dogs wood food bowl holder, it was actually a shade lighter before and had no real polish/varnish so I decided to try and do it myself. I’ve neverrr done any kind of wood work so I was nervous, but I chose this one because its whipe on! It does exactly as stated, no brush strokes left on it, super easy, dries very fast and there was no real smell! I could even do it inside in a separate room where I let it dry! Just put some kind of cloth or sheet under so if it drips, but even then it was easy to get out of the floor! Also keep in mind, it DID make my wood a slight shade darker, it is something to be informed of. It wasn’t a lot just some but important to be aware of. Mine was the satin water based and as you can see not a lot of gloss at all which is what I wanted! Just smooth! very happy 😍

Easy application, large amount for several small projects. I just wish it was a little duller of a finish or be available in Satin. The semi-gloss sheen should be great if you don't want a full on gloss on furniture. I'm using this in my modeling & on wooden folding knife scales. Do apply in very thin coats with very light very fine grit sanding in between coats for best results. My projects are small enough I apply it with my finger tip.

This is a water based 'wipe on' poly. Like all water based top coats, this covers well, is easy to clean up, and does not add any color to the base material (other than possibly darkening a reflectively flat surface). And, as a previous reviewer mentioned, this dries quickly and this feature can be a double edged sword. If you do not apply this over your entire surface within a short period of time, you can easily get ridges or overlaps that don't settle out. This particular product, however, has one advantage over all other water based top coats I've used, it is very thin (low viscosity) and is truly designed for 'wipe on' application. In fact, I would not recommend brushing this on since wiping on is significantly easier to apply the needed thin coat. I have not tried to spray it, it might spray well, but I really like the wipe on aspect and use this product where wipe on is preferred (built-ins or small projects). It is important to note that this is wipe 'on', not wipe 'in'. For each coat this should be applied in one smooth motion, with no more than a quick retrace to pick up excess. Any attempt to 'work' it into the surface will probably make the finish worse and loses the advantage of this finish, which is the ability to apply several thin coats within a day. In 4 hours I can apply 3 coats and I'm done. No sanding in between and very easy cleanup. So far I've only used this as a top coat for Milk Painted trim on some kitchen cabinets and I am very pleased with the results. My only complaint is that it is not widely available and I need to pay outrageous shipping costs for a single pint. Even with the shipping costs combined, however, this finish is worth the price.

I love this product! So easy to apply and leaves a nice sheen without being super glossy. Did have to use four coats as recommended, but they dry within two hours after each application. I would purchase again..

The plastic bottle and top worked well to get some on a rag, or with a small brush to avoid having to pull into another container. I used four coats on maple that had been stained with minwax stain. I used VERY light sanding between coats. The first two coats soaked into the wood and dried very quickly. Later coats started to look better, yet dried quickly. After four coats, the statin look was good and it seemed I was going to get the water protection I was looking for. Not much in the way of fumes. I had not problem using this stuff in a basement with an open door to a living area and then leaving the objects out to dry.

I never have much luck with polyurethane, I always end up with a drip I didn’t notice until it was completely dry. When I needed to seal a butcher block style table I found this. It was so easy to use. I used a foam brush to apply it, I tried a rag first but the foam worked much better. On the round legs I did use the rag after the foam to make sure I didn’t have and drips. It turned out wonderfully, so glad I found this product, will definitely use it again.

I found it very difficult to get an even coat on the door panels I was finishing. They were about 15 inches by 48. I really couldn't maintain a wet edge as I worked along the length of the doors. Clean up and breathing were nice. But I wasn't delighted with the result.

Mal, muy mal. Bote con tapón abierto. Y el mayor problema, deja marchas de brocha o panal y no tiene brillo ninguno. Para devolver una pesadilla!

It's a great product. I used it on the neck of my guitar. It allows you to easily put a thin coat on at a time and it dries quickly. It's eco friendly and almost odorless. Highly recommended.

Excellent result

Very easy to use and gives very good results. I am never going back to traditional brush on varnish or spray can lacquer. Gives better results with much much lesser effort than traditional varnish in a much much shorter time. Gives better results with much much less effort than spray can lacquer though takes more time. Spray lacquer can dry in 15mins. This takes about 1 hour in Singapore's sunny weather. As good as odourless. Clean up with water so easy. Can wipe on with cloth also can brush on. But as it is very thin, there is no brush lines. Minimal sanding (compared to traditional varnish and lacquer) between the layers compared to traditional varnish and lacquer. Reason is minwax is so thin. Dries pretty fast, can be as fast as 1 hour in Singapore's sunny weather. 3 to 4 layers gives me the results I want. Makes me wonder why this is not as popular as it should be. Guess is the cost.

An easy to clean alternative to oil based poly.