45 Degree Offset Rail Mount Picatinny Low Profile Adapter Mount Laser Light Rail Attachment Red Dot Optic Iron Sight Mount fit keltec sub 2000

Outstanding fit and function. Perfect for the job. Allows the PCC to fold as designed. Great value, easy install

So far it works great. Hoping it it stays solid. set screws seem a little small but it is tight right now. Will check after shooting a few rounds. Used to offset a red dot sight for a daylight/backup on my night vision AR.

I'm another person that used this for his SUB 2K. It was very easy to install, but I was concerned that it would damage my guns polymer picatinny and/or it might eventually work loose because the two set screws tighten up against the edge of the guns polymer picatinny rail. That's not the fault of this mount of course. If the rail were aluminum then there would be no issue. My work around was to grind down a thin piece of metal approximately two inches long and an eighth of an inch wide and insert it between the set screws and the picatinny rail on the gun. Then I could sufficiently tighten the screws without damaging the picatinny rail. I used thread locker so the set screws don't back out.The issue I had was when I mounted my little Sight Mark. The sight mounts on it's own base plate and that base mounts to this little offset mount. I found the base attached just fine, but it was too wide which made it difficult to properly collapse the rifle. I tried several bases with the same issue. My solution here was to grind down one side of the base plate. I sprayed the ground down edge of the base plate with four or five coats of black paint, put it all together and now my SUB could properly fold. If the little picatinny rail on this offset mount stuck out just an eighth of an inch more then this wouldn't have been a problem. As it is, I'm happy with the results.This little offset mount is plenty strong and solidly attaches to the weapon. An aluminum picatinny would not have the problem I had. I like this solution for adding a red dot reflex sight to the SUB 2K much better than the much more expensive Midwest Industries swivel mount I had been using previously. Smaller, less weight, it doesn't block the guns sights and no action is required by me to move the red dot out of the way in order to open or fold the rifle. I actually find holding the SUB at an angle to shoot to be more comfortable somehow.

It does what i need it to do. Running it with a a 1-4 single focal plane sight. Does get in the way of the sight passed 1x. Probably wouldn’t show if I ran it one notch back but it doesn’t bother me.>After shootingHighly suggest using blue lock tight. I highly recommend even though it was meant for airsoft it isn’t a functional part of the rifle so it doesn’t affect the most important cycles of the weapon.4 stars for sturdiness because without lock tight you’re gonna lose a lock bolt.

I have it installed on my kel-tec sub2k gen 2 (9mm) for a Feyachi RDS-22 Red Dot Sight. Sub2k closes and locks with this installed. Holds its position after 150 rounds and a trip to and from the range in a soft rifle bag. Does not come with the hex key so make sure you have it before installation. Great deal and recommend this if you are looking for a flush/low profile 45degree mount especially the kel-tec sub2k

I use this for a red dot sight alongside my long-range scope on a Kel-Tec rdb it melts very low which I like a lot that little extra quarter inch makes a surprising difference however my singular complaint is that the mounting screws are extremely small and strip laughably easy and will come loose over time without Loctite not as big a problem for something like a red dot but I did strip my first one and had to order a second

Exactly as described, the fit is perfect and allows the carbine to fold with the optic installed. One note: the set screws to lock the mount to the rail are tiny and it took a little time to find the correct bit that was small enough to fit the screws. It does not come with the allen key.

Where to begin?- First of all, the way that mounts doesn't work.it uses 2 set screws but even if tightened all the way down it does not fit snug and tight. It is loose. No way this will work. I am mounting it on a KelTek sub 2000 and this is advertised to fit it.- Second, I like the low profile nature of it. The gun will fold and latch with it installed. Unfortunately, once you put a sight on it forget it. And if it won't do that then what is the point of this attachment?- Third, the offset is not 45 degrees, rather it is more like 30. This is why it does not have enough clearance to close.I was really hoping that a low cost item like this would save me from buying the $150 Mcarbo product that flips out of the way but I guess there is no getting around that. I am returning this product and I do not recommend it to anyone.