Question 1

im treating a septic lagoon to kill weeds etc in the lagoon.whats best and does anyone sell it in biodegradable bombs??

Accepted Answer

How to Apply: Copper Sulfate can be applied to impounded water by the following methods:

1. Application by Dragging Under Water: By placing Copper Sulfate in a burlap or finer mesh bag, apply by dragging the bag attached to a boat or float so that bags are suspended in the top foot of water until the crystals are dissolved. Drag the bag of copper sulfate first near the shoreline and continue outward by moving as the boat travels in parallel lines about 20 to 100 feet apart until area has been treated or until 1/3to 1/2 of the surface area has been treated. Continue dragging bag over treated area until the required minimum dose is applied and all copper sulfate is dissolved. Determine the quantity of copper sulfate needed to treat the problem area following directions and precautions on the label.

2. Application by Spraying Solution on Water Surface: Dissolve the minimum required dose of  Copper Sulfate in water and spray the solution uniformly over the body of water. When spraying a solution of copper sulfate, mix copper sulfate in sufficient water to thoroughly spray the water surface. While the volume per surface acre depends on the type of spray equipment being used, spray volume should be approximately 20 to 500 or more gallons per acre of surface water. Several types of solutions and spraying equipment may be used. Observe previous cautions on the effect of copper sulfate solution on various metals in spraying containers.

3. Application by Slug Method: Make a dump of Copper Sulfate into the irrigation ditch or lateral at ¼ to 2 pounds per second of water per treatment. Repeat about every 2 weeks as needed. A dump is usually necessary every 5 to 30 miles depending on water hardness, alkalinity, and algae concentration. Copper Sulfate becomes less effective as the bicarbonate alkalinity increases. Its effectiveness is significantly reduced when the bicarbonate alkalinity exceeds about 150 ppm as calcium carbonate (CaCO3).

4. Application by Broadcasting: Dry Copper Sulfate can be broadcast on the water surface using a properly equipped boat. An air blower can be used to discharge these crystals at a specific rate over the surface of the water. When using this method, the wind direction is an important factor. Do not use this method unless completely familiar with this type of application.

5. Application by Spraying from Airplanes and Helicopters: Professional personnel licensed by the State Agricultural Extension Service are allowed to apply dry Copper Sulfate in some states. Rate may not exceed 6 pounds per acre foot of water.

6. Application by Injection in Water: A solution can be made with Copper Sulfate that can be injected in the water via a piping system.

Question 2

How much would I need to control algae on a 2 surface acre pond.  How many applications?

Accepted Answer

**these instructions are intended to direct the customer how to properly use EPA labeled copper sulfate pentahydrate, registered to control algae in water bodies and systems.

LAKES, POTABLE WATER RESERVOIRS, PONDS (Golf, Farm, Fish and Fire), FISH HATCHERIES, AND CROP AND NON-CROP IRRIGATION CONVEYANCE SYSTEMS, DITCHES, CANALS AND LATERALS: Copper Sulfate kills filamentous and planktonic algae in water. Apply at a rate of 3 to 6 pounds per acre foot of water (0.27 ppm to 0.54 ppm copper in the treated water). Apply as a uniform surface spray dissolved in at least 3 to 5 gallons of water using boat, plane or other pressurized spray device. Apply twice yearly or as needed. Determine the number of acre feet of water to be treated. An acre foot of water is equal to one acre of water one foot deep which equals 328,000 gallons or 2,720,000 pounds.  An acre foot can also be defined as an area of water 660 feet X 66 feet X 1 foot depth.

How to Apply: Copper Sulfate can be applied to impounded water by the following methods:

1. Application by Dragging Under Water: By placing Copper Sulfate in a burlap or finer mesh bag, apply by dragging the bag attached to a boat or float so that bags are suspended in the top foot of water until the crystals are dissolved. Drag the bag of copper sulfate first near the shoreline and continue outward by moving as the boat travels in parallel lines about 20 to 100 feet apart until area has been treated or until 1/3to 1/2 of the surface area has been treated. Continue dragging bag over treated area until the required minimum dose is applied and all copper sulfate is dissolved. Determine the quantity of copper sulfate needed to treat the problem area following directions and precautions on the label.

2. Application by Spraying Solution on Water Surface: Dissolve the minimum required dose of  Copper Sulfate in water and spray the solution uniformly over the body of water. When spraying a solution of copper sulfate, mix copper sulfate in sufficient water to thoroughly spray the water surface. While the volume per surface acre depends on the type of spray equipment being used, spray volume should be approximately 20 to 500 or more gallons per acre of surface water. Several types of solutions and spraying equipment may be used. Observe previous cautions on the effect of copper sulfate solution on various metals in spraying containers.

3. Application by Slug Method: Make a dump of Copper Sulfate into the irrigation ditch or lateral at ¼ to 2 pounds per second of water per treatment. Repeat about every 2 weeks as needed. A dump is usually necessary every 5 to 30 miles depending on water hardness, alkalinity, and algae concentration. Copper Sulfate becomes less effective as the bicarbonate alkalinity increases. Its effectiveness is significantly reduced when the bicarbonate alkalinity exceeds about 150 ppm as calcium carbonate (CaCO3).

4. Application by Broadcasting: Dry Copper Sulfate can be broadcast on the water surface using a properly equipped boat. An air blower can be used to discharge these crystals at a specific rate over the surface of the water. When using this method, the wind direction is an important factor. Do not use this method unless completely familiar with this type of application.

5. Application by Spraying from Airplanes and Helicopters: Professional personnel licensed by the State Agricultural Extension Service are allowed to apply dry Copper Sulfate in some states. Rate may not exceed 6 pounds per acre foot of water.

6. Application by Injection in Water: A solution can be made with Copper Sulfate that can be injected in the water via a piping system

Question 3

willthis control the weed coontail

Accepted Answer

Copper Sulfate is not typically used to treat aquatic plants, but some are labeled to treat the invasives Eurasian watermilfoil (Myriophyllum spicatum) and curly-leaf pondweed (Potamogeton crispus), as well as the native species coontail (Ceratophyllum demersum), naiads (Najas spp.), elodea (Elodea canadensis), sago pondweed (Stuckenia pectinata) and water celery (Vallisneria americana).   Determining the correct copper formulation and calculating the proper dosage are key factors in determining how well copper will control undesirable algae and pond weeds.

Question 4

what is chemically different between this product and the cheaper non EPA registered???? Isn't copper sulfate pentahydrate the same molecular formula?

Accepted Answer

yes it is the same molecular formula BUT the EPA requires us to label our copper sulfate with an EPA approved label as it is being used for algae or root control.  Non EPA labeled copper sulfate is the same but we are not allowed to advertise it for use against algae or roots.  Non-EPA copper sulfate should be used for any reason but killing roots, fungus, and algae.  EPA copper sulfate should be used when you are trying to eliminate or kill an organism of ANY fashion.  We are the only EPA compliant company that sells copper sulfate on amazon.

% Assay of Chemical(s)	99.9
ASIN	B01KIORC58
Best Sellers Rank	#212,757 in Industrial & Scientific ( See Top 100 in Industrial & Scientific ) #408 in Life Science Supplies #1,623 in Lab Chemicals
Brand	BBear
Brand Name	BBear
Container Type	Bag
Customer Reviews	4.5 out of 5 stars 82 Reviews
Item Form	Copper
Item Weight	50 Pounds
Manufacturer	Earthworks Health LLC
Package Information	Bag
Part Number	COPPEREPASMALL
Percentage assay	99.9
UPC	756519496918
Unit Count	800 Count

Copper Sulfate Small Crystals 50lbs Bag - EPA 99% Pure

Details

Details

Description

Specifications

Common Questions