NETGEAR16-Port PoE/PoE+ Gigabit Ethernet Unmanaged Switch with 76W PoE Budget (GS116LP)

Great product... exactly as per advertised specs.

PROS: - true 802.1q VLAN tagging support, at a very low price - excellent wire-speed performance, tested @ 950+Mb/s in iperf on 6 ports at once, so long as Flow Control is disabled (see below). The main chip is a Broadcom BCM53128, which seems slightly faster and more efficient than the Realtek RTL8380 used on competing switches from TP-Link and Zyxel. - very low power use, approx. 1W - 3W dependent on ports in use (~ 0.25W DC / 0.45W AC base plus 0.3W per connected 1000M port, or 0.2W per 100M port). Traffic levels seem not to affect this much, though cable length might, since it tries to use lower transmit power on short cables. The switch-matrix core runs on 1.2V, with 3.3V for I/O, both provided by efficient switchmode buck regulators (unlike some switches that use a hot-running, linear step-down from 3.3V to 1.2 or 1.8V, at < 50% efficiency). - silent operation, with no fan or coil whine. Despite the lack of a fan, mine never even gets noticeably warm. There is a reasonably sized heatsink on the main chip, and a thermal pad under the PCB, allowing the case bottom to serve as an additional heatsink. - good build quality. Just one electrolytic capacitor, which is a Nichicon (reputable Japanese brand) 220uF on the power input, over-rated at 25V when operating at 12V. Main switch chip is a Broadcom BCM53128. Case is solid metal, compromised slightly by a stick-on platic piece around the ports for labeling, which another reviewer complained about. - happily runs on the variable 12V battery bus (10.5-14.4V) from an offgrid DC power system - starts up quickly, from cold-powerdown to forwarding traffic in about 8 seconds, far faster than any "true" managed switch (Catalyst, Juniper, Procurve etc.)CONS: - management interface, whether via web or Windows app is limited and cumbersome, especially when configuring VLANs, though is most cases this is only a one-time annoyance, set-and-forget - typical of switches in this class, there's no CLI management, nor SNMP, so tracking port activity with MRTG, etc. is not possible. Omitting these probably does reduce both cost and power use, though. - The management controller, integrated within the BCM53128 is a weak CPU derived from the 1980s-vintage, 8-bit Intel 8051, which is easily overloaded. This explains the lack of HTTPS SSL support, occasional dropped HTTP requests, etc. It's actually impressive they managed to squeeze an IP stack and web interface onto such a small CPU at all. - This limited 8051 service processor would only affect management functionality (it isn't part of the main switch-fabric data path at all), except for a dumb decision on Netgear's part to configure the switch registers to send a copy of *all* HTTP (tcp port 80) traffic, originating from any port, to this tiny management CPU.This has the effect of badly crippling the layer-2 Flow-Control feature, causing any and all HTTP traffic flowing through the switch to be bottlenecked to about 10Mb/s whenever Flow Control is switched on. The reason is that flow-control rate limiting kicks in whenver any port receiving the traffic gets overloaded, the weak management CPU effectively connects to a internal 9th, on-chip port that seems to run at only 10Mb/s, AND all web traffic from anywhere to anywhere (even when bearing an 802.1q VLAN tag!) gets uncontrollably copied to the phantom port-9.This wouldn't be so bad if the web interface could be moved to a less important port than tcp/80, set to listen to requests only from one specific switch port, or disabled entirely (until next power-cycle, say, or even semi-permanently until a factory reset), but none of these options are provided.Netgear does seem to ship these switches with Flow Control turned OFF by default, masking the performance problem, and in many cases Flow Control is undesirable anyway, but it can be useful in cases where a node on your network can't keep up with full Gigabit rates, but can do better than 100M. Many low-power single board computers fall into this category and can benefit from FC.The management controller can also be a big security hole, since it doesn't respect VLAN boundaries at all, and copies of its transmissions get relayed to ALL ports, in-the-clear and untagged, regardless of VLAN membership status. The switch effectively reverts to just a dumb hub whenever the hidden Port 9 is involved.HARDWARE MOD:If you don't mind voiding your warranty with a small bit of soldering, it's thankfully possible to disable this ill-behaved web interface and completely disconnect the BCM53128's 8051 management controller from its switch fabric, eliminating its security exposure and letting Flow Control work as intended, with no more weird slowdowns affecting port 80 . Here are the steps:1. First Get everything configured as you like in the web interface, setting up and testing all VLANs, etc. Reboot the switch and verify it comes up in the desired configuration.2. Open the cover and find tiny surface-mount resistor R75, between the main chip and the ports, near the crystal oscillator. Desolder this resistor. See my first photo, where it's already been removed, leaving bare pads.R75, which I measured at 4.4k in-circuit, pulls BCM53128 pin 43, "EN_8051_TxRx" high, to 3.3V. It CAN just be left floating if you don't mind losing the web (and Windows-config-tool) interface permanently after initial setup.3. If you want to be able to toggle the web interface off and on, solder a very fine-gauge wire to the removed R75 resistor's pad nearest the main chip, and another such wire to a 3.3V power pin anywhere on the board-- you could use the other side of R75, but it's easier to grab this voltage from a less closely-spaced area. I chose to use the power pin (pin 8) of U5, the 8pin serial EEPROM at upper-right.4. drill a hole on the back panel somewhere to mount a small toggle switch. Solder one of its terminals to the R75 pin (BCM531128 pin43, EN_8051_TxRx signal) through a 3.3k-ohm resistor. Solder the other toggle switch terminal to any convenient 3.3V pin, through a 1k-ohm resistor (optional - these two resistors in series approximate the original 4.4k-ohm pullup, but anything in the ballmark should work)Note that EN_8051_TxRx is only latched during reset, so after flipping the switch you have to power-cycle the switch for it to take effect. At least this Netgear is fast to reboot, but having to do so makes its port traffic & error counters effectively useless, unless you leave management enabled all the time.If you want to add a RESET button also, solder a fine wire to the right-hand (near the coil) terminal of resistor pad R7, which should be empty to begin with. This goes to the Shutdown terminal of the 3.3V switchmode regulator, and grounding it (through a 1k-ohm resistor) even briefly will cause a clean reset via 3-pin power-supervisor chip U3. That IC actively drives the BCM53128 RESET pin both high and low, so you can't safely pull RESET down directly.Rather than mounting a physical toggle switch, since my GS108e is in a hard-to-reach spot I decided to bring out these control signals (EN_8051_TxRx, +3.3V, RESET-via-regulator-shutdown) to a 4-pin header, which plugs into GPIO outputs on a nearby router, allowing management-enable and reset functions to be controlled remotely. Anyone going this route should ensure both systems share a common logic ground, and take care to never drive either signal to more than 3.3V Documentation on the BCM5128 is hard to come by, but I very much doubt it's 5V-tolerant.

I bought this for a small home rack to replace the need to use a POE injector. Moved all of my security cameras to this switch and it has worked flawlessly for several weeks now. I really like the external power supply as you can upgrade the power to support more POE devices if needed. The switch is also pretty small so it fits great in a small home wall mounted rack. Note that it’s not 19” wide, but comes with special mounting brackets. Note that the mounting brackets aren’t a full 1U high and leave gaps. This is beneficial to me for air flow, but some people may not like this

I've been using this particular product for quite some time now and I must say, it's been a solid investment. I've actually accumulated quite a few of these switches, and they've proven to be a great value, especially considering they are managed switches.One of the features I appreciate the most is the support for VLANs, and let me tell you, it's surprisingly affordable. If you're looking to set up VLANs without breaking the bank, this switch is definitely worth considering.In terms of performance, it does exactly what it's supposed to do. The switch has a desktop or wall mount option, making it versatile for different setups. Plus, the limited lifetime protection gives me peace of mind that I won't be left high and dry if something goes wrong.Overall, if you're an average person like me, looking for a reliable switch that offers some advanced features without burning a hole in your pocket, I'd highly recommend giving this one a try.

No issues at all. No complaints. Very good product.

Purchased this unit to replace the OLD unit which "just finally quit".Swapped them out and everything's up and running again.