Thermalright AXP90 X47 Black Low Profile CPU Cooler, with 92mm TL-9015B Slim PWM Fan, ITX CPU Cooler, AGHP Technology, 47mm Height,for AMD AM4 AM5/Intel 1150/1151/1155/1851/1200/1700(AXP90 X47 Black)

This Low Profile CPU cooler is good for keeping relatively low wattage CPUs cool. I have it installed on P8H77-i ASUS motherboard with an Intel Xeon e3-1230v2 CPU (69W TDP according to Intel). I think the max temp that I saw was 74°C while gaming. It's not too loud either. The installation is not for a first time builder. Now, installing this cooler is an experience. I believe it is referred to as a reverse install. The standoffs are to be installed to the heatsink which *should* extend through the metal backplate. You then hand tighten the fasteners. Make sure you check the edge of the motherboard for flexing. If your motherboard is flexing, the fasteners are too tight. Overall, it's a good low profile 90mm CPU cooler for a low power, small form factor (SFF) build. Follow the installation instructions and be mindful of how tight you tighten the fasteners, it'll be satisfying to know you didn't bork your motherboard when it boots and isn't overheating.

Smooth install and it works great so far. I will look for this brand the next time I need a cooler.

The fans relatively quiet seems to cool pretty well just the mounting is a little bit finicky but apart from that it cools well and has been working well

This is a nice cooler...it is in a inwin b1 on a 5700G built around the ASRock b450 itx fatality...my main complaint with noctua similar but more popular offering is the direction it vents, it pushes air out left and right vs up and down so basically airflow is cut off by the memory and IO area ..this one from thermalright is exactly opposite it vents out the top and bottom(with convection mostly top) so this little problem as basically gone, the mounting mechanism defenetly isn't noctuas famously easy to use one but it's effective and considering I'm not going to be taking the cooler off twice a week it's fine and iv defently seen worse on soposedly high end cooling solutions so I have no complaints...if I were to pick a single thing to hone in on with this brand it's the smorgusborg for varients they offer, 36mm copper(black or gray) 43mm aluminum copper or black copper, 53mm in all versions mentioned above, all difrent weights...ya it's a bit much for your average consumer...but that being sead I was able to find 2 that I liked that would not only maximize the height in my specific case wile leaving enough of a gap to pull in air but I also had a choice of color so there is that...but I think to drive my point home here I ended up buying 2 one all black that is soposed to be coated copper and one that is just all copper becase aperently even tho they are the same under the coating they are showing in the description as difrent weight and wattage so we will see about that once I receive the secound all shiny copper heavy one lol...overall I like them they are not over engenered just to make a basic mistake like push the air in a direction that on every itx motherboard made in the last 10years has many large tall things called ram modules RIGHT there basically eliminating any benefits of your product being heavy dense and well built lol...good job thermalright you didn't forget the basics ----------- Update I just received the full copper revision of this model and yes it is infact noticeably heavier...I will defently be swapping out the all black one for this one and pairing it with the noctua slim 92mm fan from a nh-l9a and probebly artic MX 4 compound and doing some before and after testings on all the difreces...I'm not realy shur why this model is heavier than the black one as the black one is soposed to be full copper aswell just painted with a thermaly conductive paint and also nickel plated but we are going to find out what the results are of the difrences after testing...I want to be clear I like the all black model and the fans on these are ok, I will not be returning whichever one I don't use for this build long term I just want to make shur I am pairing the best possible solution with this 5700G to get the best possible cooling performance so I don't have to worry about my CPU temps in this airflow anemic case that is the inwin b1...lol I will likely just copy and paist this review for the copper one so there is a bit more feedback for both models becase as of right now there is very little user feedback on these and that a shame as they both have the same benefits over the noctua LP coolers that being they blow air up and are not blocked off by the memory or IO area(cooler or integrated sheald) but all the info in this review is still relevant for the copper one especial this part lol

Bought this to air cool an i9 10850k in a Formd T1 (I would recommend not using this CPU if possible, but it was what I had already). It is just about the tallest air cooler that can fit in said case while in 3 slot GPU mode. I had planned to reduce my TDP in bios since the 10850k runs very hot, but this cooler along with some noctua case fans were able to keep it just cool enough during my Prime95 stress test. It did not get too loud either. Extremely impressive! The only gripe I have is with the mounting solution, as it is not straightforward and is possible to overtighten, which could lead to damage. I was able to get sufficient mounting pressure via hand tightening, but your mileage may vary. I would err on the side of caution though. Still, considering the lack of other air cooling options with this leveling of cooling capacity at the size it is, I still give it 5 stars. If I could rate in non whole star numbers I'd probably say its a 4.7. I will update this review if it ever gives me any problems.

Very easy and clean install with AM5 cpus and my Ryzen 5 7600x runs 40-50c while gaming at 4k. The only thing you have to be aware of is that this cooler comes with multiple different pieces of hardware for mounting different socket types and if you plan on using it for AM5 I would suggest using the longer screws with the stock backplate and not using a screwdriver with the socket tool they give you for tightening down the nuts as I heard you can risk over-torqueing them, so stick to only finger tight. I would definitely recommend this cooler over the Noctua l9a as the mounting method on that is a real pain because you have to line up the holes without a guide, which can get messy and the screws end up stripping, which is unfortunate for a product that costs double the amount this cooler does.

Mounting hardware came in damaged, made install difficult

Noticeably quieter and cooler (around 5C different) than the AMD wraith cooler I had been using. It's nothing crazy, but it feels like great value for this price point and form factor. If you have budget for an extra $30, probably it's best to get a noctua product. If you have extra space, probably it's best to get a cooler with a larger heatsink

Muy buen producto

Çok iyi bir soğutucu. Dünyada bu form faktöründe en iyilerinden biri sanırım. Türkiyede bu tarz ürünleri bulabilmek sevindirici. Satıcı, full copper versiyonunu göndermiş. Teşekkürler.