







Desertcart purchases this item on your behalf and handles shipping, customs, and support to Seychelles.
⚡ Stay Powered, Stay Ahead – The Ultimate Battery Isolator for the Modern Driver
The Battery Isolator 100A by BATTERY DOCTOR is a compact, water-resistant (IP62) automotive accessory designed to safely manage battery power flow. Featuring a 100-amp capacity and included mounting bracket, it ensures easy installation and reliable performance for trucks and cars alike. Perfect for professionals seeking durable, efficient battery management solutions.
| ASIN | B004QCDE9M |
| Amperage | 100 A |
| Best Sellers Rank | #150,204 in Automotive ( See Top 100 in Automotive ) #622 in Battery Chargers |
| Brand | WirthCo |
| Customer Reviews | 4.4 4.4 out of 5 stars (160) |
| Date First Available | December 23, 2010 |
| Item Weight | 1 pounds |
| Item model number | 20090 |
| Manufacturer | BATTERY DOCTOR |
| Manufacturer Part Number | 20090 |
| Model | Battery Isolator, 100A |
| OEM Part Number | 20090 |
| Product Dimensions | 10.5 x 6.7 x 2.3 inches |
| Safety Rating | Não Aplicável |
| Voltage | 12 volts |
D**N
new generation of battery isolator.
this is a new method to maintain 2 batteries in a boat or RV, but keeping them isolated. It works well, requiring very little in the way of installation. (couple screws, couple wires, etc). If you are old school and know about the larger diode charging blocks (typically 2" x2" x 5" with large cooling fins) this is will do a similar function, but in a different way. This has a circuit to monitor the voltage, and when the main battery is charged enough, it will open up the charging to the aux battery (think boat starting and trolling motor). so as the first one charges up, the second will then begin charging. I contacted to the company to get their insight if would work correctly with an "A/B/Both" battery switch and they assured me that it would work (always turning on the battery to A, unless you have an issue, then you can use B or Both without worrying about the battery doctor having problems. the product does pull about 30mA when the boat is not running, and the way I have wired it, this happens even if my A/B switch is off. 30 mA will take a long time to drain a 100Amp Hour battery, but it is something to know for long term storage. I also added a trickle charger at the same time and this will actually allow the trickle charger to charge the main battery first, and then open up to charge my aux battery second. never wanting to be caught without a battery on the lake, this is an important component for my boat.
T**Y
works easier then described.
as described I attached the unit to sheet metal with velcro, then black wire to ground and finally first power from fused auto to main terminal and then power from aux terminal to second battery positive terminal. all in all, 5-10 minutes including making custom cables. When ground wire first attached, nothing happened, then when attaching power from car, I got a flashing red light, now with second battery terminal hooked up, I got solid red. start engine and after 5-10 second delay you see a bright blue light, just as described. You can make your own relay set up, however both batteries will be in parallel, to start car, with this unit only starter battery is used. Now if starter battery dead just push a button which activates relay, and both batteries now in parallel to start your car. there is a model 20092 which is rated at 125-150 amps instead of 75-100 amps, which had I known about I would have spent the extra $20 or so on. Needless to say it worked perfect and extremely easy to install. With this unit you can throw away your booster cables as they will no longer be needed.
F**S
works great - updated (LiFePO4)
Update 2023: when my FLA bank died I replaced it with 150Ah of LiFePO4. I assumed I'd need a DC-DC. But I fired it up with the VSR in place and it works fine. Over the last ~20 runs, the average state of charge before start was 72%, bank voltage 13.20v. Charge acceptance after start was 0.183C (27.39A). See note below about using a switch to deactivate the VSR when desired. ------ I've had the isolator installed for [three years] and it has worked great, no problems. I would like to bring up a few points: * folks often say that this voltage-sensing relay connects the Aux battery when the starter battery is "fully charged"; that's not really what happens. Per the manual and my observation it makes the connection when the starter battery is >= 13.4v. Lead-acid chemistry batteries take hours to get "fully charged" (100% state of charge). In practice this means you'll start the vehicle and a few seconds later the relay will 'click' and you are connected. I don't know but I suspect this stepping-up in load is easier on the alternator. * if you are charging the aux battery[s] from another source while the batteries are connected (engine running, or recently turned off) any 13.4v+ charging voltage will be seen on the starter side and the relay will not disconnect. This may or may not be what you want. See below. * you can put a switch on the slim ground wire to deactivate the isolator. This might be useful if you want to do something like equalize the house batteries without feeding that voltage back to the vehicle. [I installed a High Voltage Disconnect (a few bucks here on Amazon) to disconnect the Doctor when solar raises the house side above 14.1v.] [I read a report about one of the connectors getting overheated - I suspect that person had a loose connection that overheated and melted the plastic. Remember to check your connections when you maintain the battery bank!]
A**R
90 Amp
4 cyl car 15 years old it ran with the batt in the boot before. I do wind power and this purchase 90 Amp battery doctor is a transition phase before going a little into solar. I had pre-existing wires and connectors. Rather than deep cycle batt I am using sel batt that was on hand in good condition. I like the unit, it connected as described in the instructions . I am back to adding accessory electronics in the car. Purchased this with a gift card because I run 90 amp , I want accessories & now I push an inverter to run lighting and little heating if needed during cold months. Unit works to my ideals
A**R
Great product! Easy install!
Easy install on my Kawasaki mule 600. I use it to have a separate battery to run sound system, neon lights, ect. I ran these accessories all day and night, starting the mule with no problems to charge second battery. I previously purchased an old school isolater, but couldn't figure out what wire was the charging wire coming out of the little grey box. This battery doctor solves/cut out that problem.
L**K
Good product with some problems.
I like the product with some instillation issues. I have two of these units in my boat. One for auxiliary, one for trolling motor battery's. Both battery's are charged from the engines alternator. This setup had worked for several years till this spring, one failed do to water penetration. Although the installation is simple the instructions need to include critical assembly of wiring of battery cables. Some of this information was told to me from Tim from there tech support team witch I found better then most support you get now days. If you notice the plastic around the base of the post crack or you can see the o rings that are supposed to seal the post, you can assume the unit is no longer water resistant. I reinstalled my units in a industrial waterproof box (x stream overkill). A Tupperware box would probably work. 1. The flat washers (included) needs to be put on post terminals first. Under the battery cables. 2. The size of the terminal hole on your battery cables must be as close fit as possible to the post. If it is to large (as in my case) the flat washer will bend causing the plastic case to fracture around the post, allowing moisture to penetrate the otherwise well made enclosure. 3. Do not over tighten post nuts. As you tighten the nuts observe the lock washer (included), once it is fully compressed cation must be taken to not go much further.
S**S
Works perfectly
This thing does a great job. Separates two batteries, one for truck and one for the plow itself. Charges one full, then goes two the other one. Awesome! No more draining the starter battery down. Would not have a plow truck without one. This thing is priceless!!
M**K
Great mod to our camper
Worth every penny. I have a power wire coming from my Jeep's main battery to the plug in the picture. Then a plug and a power wire to the isolator then to the battery in my camper. Now I can charge the camper battery while my Jeep is running without draining power from my main Jeep battery. Great mod to our camper.
J**C
Buen funcionamiento!
Hasta el momento a funcionado bien, es de buena calidad.
A**R
Easy to install, works great
Compact and waterproof design. I especially like the over ride/boost function. Any body want some old booster cables?
A**O
منظم شحن ممتاز
ركبته في سيارة سلفرادو ، ويشحن البطارية الاساسية والاحتياطية ممتاز جدا اوصي به
2**S
السعر
شكرا
J**T
Works as described and was super easy to install
Works as described and was super easy to install. If the red light is flashing you just have to put a ground from the auxillary battery.
Trustpilot
1 month ago
5 days ago