Performance Tool W80526 6-Piece Non-Magnetic Brass Blades Set for Electronic Ignition Distributors, SAE 006-016in & Metric 152-406mm Sizes

Nice set of non-magnetic feeler gauges. Use these to set up brushless RC buggy motors. This set it brass. It's very difficult to use steel gauges because of the strong magnets in the RC motors.

Hard to find a metric only feeler gauge locally. Everybody sells combination SAE/Metric feeler gauges.Blades were soaked in oil, so I had to give them all a good wipe down before I checked them with my digital caliper. Thought it was missing a couple of the smaller gauges, but they were just stuck together with oil.Measured all the gauges with my digital caliper, and they were all pretty much spot on except .04 through .09 mm. All those were .01 mm small according to my digital caliper. .04 was .03 and so on all the way to .09. Just measured the tip of the gauges, so they could have been spot on at other areas of the feeler gauge surface.These are good enough for what I need them to do, and right now that is to properly adjust a throttle position sensor.

Just as they describe. These are being used to set the point gap on my 1971 vehicle and to double check spark plug gap. The tools has worked great so far and I do not see any issues with it provided standard care.

Used it on my 08 civic for valve adjustments....This is an awesome little tool. It doesn't allow you to "cheat" on a valve adjustment leaving it too loose. Just need to worry about too tight using this.I used this with a set of standard angle feelers, checked my valve clearance twice, torqued down and voila! Done without any worry.

I think they soaked this tool in an oil bath for a week, pulled it from the bath and shipped it right out. The amount of oil on this tool is insane. That said, the oil might well be necessary to ensure to adjacent, smaller blades don't stick together and give inaccurate readings. So, assuming that's the case, I'm giving it 5 stars. Stick to blades for measuring spark plug gaps!

Bought because of price and figured Go No-Go would be pretty easy with a two (2) thousandths variance between the tip and body of each leaf. Boy howdy was I wrong.Verified size using calibrated 0-1 inch L.S. Starrett friction thimble micrometer. Only had to measure one leaf, .004 .006 The smallest dimension was .0045 and that was way inside the tip right at the edge of the step to .006. Didn't bother measuring .006 because that .004 actually started at .0055. Yep, if you want to slide in on .004 you can't get there without first passing almost the upper stop point at .0055. Zero ability to go / no-go.This is supposed to be a precision ground blade with perfect thickness on the upper limit and ground perfect two (2) thousandths under-size on the tip for the go part. Being off by one and one half (1.5) thousandths is well beyond unacceptable.Full refund and keep item. Will have to follow up and see if main parts are correct dimensions before the messed up ground parts. Otherwise, this item would be better in a recycle bin, and never ever used for measurements.

Good feeler gauge but gauges are coated in a lot of oil so they tend to stick together

For setting intake and exhaust valves on a URAL motorcycle... these are like having a third hand. Speeds up the process especially when leaning over between the valves and the side car. Good value

Brass Perfect for small engine repair to ajust coil gap

El producto es lo q necesitaba en mi caja de herramienta ya que soy técnico en aeronáutico, muy buena marca y calidad la recomiendo

Good quality feeler gauge set, oiled from factory so they won't rust. Go-no-go feature makes valve adjustments a breeze.

Exacle as decribed. Good quality guage will last a lifetime

Excelente herramienta, viene con demasiado aceite lo que dificulta su manipulación al principio pero cumple su función. En relación Precio / Calidad está muy bien.