1T2 Y-Splitter Extension Wire with Julet Type 3pin Connector for Bike Headlight/Gear Sensor/Brake Split Cable (3pin, 7" in Length)

Gotten this to split into the ebike signal&power wire for the rear light panel. Matched the ebike's head central controller connector perfectly, it is snug waterproof connection and even color coding is matching. Wanted to wire one of the split ends to front turn signal&voltage cables while the other end connects to rears. Never worked, even though I made sure and measured voltage that was going to the rear light panel and measured 12V which is also what the front sequential led signals take. There was flashing, always on right signal all the while rear ones worked normally, but in certain polarity exchange ebike head unit even threw some error code, E23 if I remember correctly. Perhaps I need specific electronic bridge or step up step down modules? Iiii dooont knoooow. But if you do please help what could do the trick as I'm desperately trying to get front turn signals working. Nice item regardless, and thankful there is supplier with this type of stuff. Rare yet cheap, thankfully quality is there as well.

I used this with 5 pin relay to activate brake light when brake lever applied on 4 stroke motorized bike. Worked as anticipated. 5 pin relay, yellow wire constant for running tail light, when relay triggered, blue wire to led flasher, then brake light on load. I used the red and yellow wires, one to ground, and other to trigger relay. Omit the black wire. This isn't the intended use for this wire, but it works perfectly. You will also need https://www.amazon.com/dp/B0CHJ7DTR7?ref=ppx_yo2ov_dt_b_fed_asin_title&th=1 and E-bike Hydraulic Brake Sensors Cable for Bafang BBS BBSHD Motor Power Cut Off US / not available on Amazon, I found mine on Ebay

Good item and service.

Bought the short splitter to add a cell charger to my ebike. My only complaint is that there should be a really short version offered with little or no wire as this one adds around 18" of unnecessary wire clutter. Otherwise it did the trick, matches perfectly and works great.

worked like they should, nice and long

I spliced into my e-bike cable to supply power to a volt meter. No cables/ connections were damaged in the process. I also purchased a pig-tail to plug into the second connector on the Y-splice, which l hardwired to the voltage meter. All worked out great. It may be overkill, but I put heat shrink over my connectors since it rains a lot here. Cost seemed reasonable. It's nice to know the exact voltage rather than depending on the 5 bars of the panel.

Virtually great the life splitter powers, the light bar in the elite headlight on my lectric xpedition 2.0

It fit, and for a few seconds I thought yeah and then both the controller and the display quit working.

Passt perfekt

L'article commandé est conforme à la description, ce qui m'a permis de réparer mon speed pedelec Riese Muller. Je recommande...

it is as shown.It works

Useful For Upgrading Ebike, used to split display julett connection and fit voltmeter using a 5 pin male julett fly lead and solder voltmeter wires to appropriate wires, in my case everything connected through the splitter is working correctly.

Dieses Y-Split Verlängerungskabel ist genau das, was ich für meinen E-Bike-Umbau gebraucht habe! Die Verarbeitung macht einen richtig hochwertigen Eindruck, die wasserdichten Stecker sitzen fest und sicher – perfekt für alle Wetterbedingungen. Die Signale für Licht, Bremse oder Getriebesensor werden zuverlässig übertragen, ohne Verzögerung oder Wackelkontakt. Die Installation war total unkompliziert: Einstecken, Kabel sauber verlegen – fertig! Besonders praktisch ist die Auswahl an Pin-Varianten, sodass man das Kabel genau passend zum eigenen System bestellen kann. Für alle, die ihr Ebike erweitern oder optimieren wollen, ist dieses Split-Kabel eine super Lösung. Top Qualität zum fairen Preis – klare Empfehlung! 🚴‍♀️🔌✨