SCYTHE Glide Stream 140mm x 25mm PWM Fan - 500-1300 RPM SY1425HB12M-P

works great as intake fan

Ventola particolare perché è da 14 ma con attacchi da 12. L'estetica è carina la scatola tutt'altro la fa sembrare tremendamente cheap. In realtà tralasciando i fronzoli (ti danno una ventola in una confezione bruttina, ben diverso da quel che offre una buona noctua) la ventola in se è davvero ottima, si sente come giusto al massimo ma spostando tanta aria e sempre senza essere un phon, mentre tenendola a rotazione inferiore (è anche PWM) il rapporto aria spostata/rumore è perfetto decisamente silenziosa. Alla rotazione minima da tenere in idle ovviamente nulla da dire, il range di giri è perfetto basta regolarla in maniera ottimale da BIOS.Peccato si cominci a non trovare più nemmeno questa da quel che vedo, Scythe ha la strana tendenza di far sparire le cose buone che fa.

Ventilador de gran tamaño para una caja de pc. A pesar que el ventilador es de 140...los anclajes son los mismos agujeros que los ventiladores de 120. Parece algo ruidoso para lo que estoy acostumbrado en ventiladores de 140....estaria bien que viniera con una resistencia para bajar el voltaje y la velocidad.

Sehr gut geeignet als CPU-Lüfter, ich verwende ihn zusammen mit einem Scythe Ashura Semi-Passiv CPU-Kühler ( http://www.amazon.de/Scythe-SCASR-1000-Ashura/dp/B00B7DDDL2 ) für eine AMD Phenom II- CPU, dort ist er praktisch immer unhörbar durch das Gehäuse.Als Gehäuselüfter ist mein Exemplar nur bis ~9V wirklich leise. Bei maximaler Drehzahl (12V) ist er sehr laut.Dennoch in Kombination mit (beispielsweise) dem sehr günstigen Speed Controller von Titan funktioniert er auch als Gehäuselüfter hervorragend ( TTC-SC01 www.amazon.de/gp/product/B000YIQ19M ).Fazit: für CPU-Kühler sehr gut, als Gehäuselüfter in Kombination mit einem Speed Controller ebenfalls sehr gut. Bei voller Drehzahl (etwa wenn man ihn direkt an das Motherboard ohne Speed Controller anschließt) zu laut. Aber gute Speed Controller gibt es bei Amazon schon ab rund 5€.

J'ai acheté se ventilateur pour le mètreà la place de celui d'origine sur mon dissipateurde proc Thermalright HR02 Macho Rev.A (B-W)Il s'adapte parfaitement même mieux que celuid'origine, je passe de 73 cfm à 97 avec le Scytheet j'ai gagné en refroidissement 3,4 degrés monproc doit être ravis,alors que dire de plus àpart nickel. Merci à AVIDES pour la préparationet l'envoi de ma commande ainsi qu'Amazon bien sûr.

I bought this fan along with a 120mm fan from another company in order to replace the stock 140mm and 120mm fans that come with a Noctua NH D-14. Those fans are only three pin and so always spin at full RPM.Anyway this fan is nice and quiet at low RPM and it's not annoyingly loud at full, the fans on my graphics card are louder than this when playing games so it just gets drowned out.Couple of things worth noting (which I don't think are in the description) are that this is a 140mm fan with fan mounts for a 120mm fan. This was perfect for my purposes but it wont match the holes in your case for the 140s and in my particular case the 120 mounting areas wouldnt allow me to install the fan properly. This isn't an issue with the fan as such but I thought it worth mentioning. In case you plan to install it in a 120mm slot you should check your clearance around the screw holes.Also when trying to use this with the Noctua I had some difficulty as the screw holes are actually rubber sections pushed into an open square area in each corner. This is actually shown in one of the product pictures but as one side of the rubber is raised above the plastic of the hole it meant I couldn't fit the shaped metal wiring that connects the fans to the heatsink. I had to cut the nibs off each corner piece in order to fit the wiring. This isn't a complete disaster as technically there are 8 of these rubber pieces (one for each corner and on both front and rear of the fan) meaning I could swap the rubber pieces around if I really needed to fit the fan to a case mount.In terms of air shifted this is actually a pretty good performer. It seems to produce a nice gust at full RPM and didn't negatively impact performance of my cooler (I haven't actually checked whether there was any increase in cooling). The cable going from fan to socket is nice and long and feels pretty thick and durable.All in all not bad considering at time of purchase this was the cheapest 140mm PWM fna available. You could find better, but it'll cost more and they likely won't have the low profile this fan