Mist Coolant Lubrication Spray System for Metal Cutting Engraving Cooling Sprayer Machine for Air Pipe CNC Lathe Milling Drill

Nice set. I’m not sure about the “misting” as I’m only using air this far. Nozzle seems too big for a hood mist.

I cut and drill 1" X 1" stainless steel bar and have been using Tap Magic EP-EXTRA as a coolant (another great product, by the way!). I used a 12 volt pump I had to create a flood system for my band saw, but it would have been too much for my drill press. After reading all of the positive, helpful reviews this sounded like the right thing. I had an air regulator and gauge from an old compressor and hooked it up in line with this unit and it works great. It allows me not only fine tune the amount of pressure going in, but I can cut off the air flow easily, also. It comes with the syphon hose for the fluid, but not the air hose. You can get the 5/16" tubing at Lowes, but their compression fittings for that size are limited. Because of this, to connect to my regulator I had to start with 1/4" tubing and transition up to 5/16". You can probably find the correct fittings on line, but I kind of like the challenge of figuring out a solution with what you are given. How does it work? Great! Because of the misting, it's hard to gauge exactly how much coolant is actually going down the hole. so periodically i will back off the press and let it lubricate the tip of the bit. The nozzle was getting smacked by the strands coming out of the hole, so I reinforced it as you can see. No magnet? No problem... for me, anyway. Mine will stay in place indefinitely. Excellent product that I highly recommend.

I use this on my CNC mill to blow air or coolant. It works pretty well. If I had it to do again, instead of mounting it to the mill, I plan to attach some strong magnets (B0BDDNQ3PB) so it is easily repositioned. I would have loved a slightly longer gooseneck, but it works fine. I ordered from Amazon the ASIN=B0836DJD4J tubing to connect it to my compressor. Everything works great. The controls are ok, and no leaks or issues. So far it has performed well.

This product works as described (mist/spray using an air compressor), so 5 stars. Also great value. However, I want to cut aluminum on my CNC and prefer to apply a stream of liquid rather than a mist/spray, so that it shoots a sufficient volume and pressure of liquid to clear the chips in addition to providing cooling. So, I kept the housing of this OriGlam product, and swapped out the hose with this product: Loc-Line 40413 Coolant Hose Assembly Kit, Acetal Copolymer, 7 Piece, 1/4" Coolant Hose ID https://www.amazon.com/dp/B006R9O3HE?ref=ppx_yo2ov_dt_b_product_details&th=1 Instead of an air compressor, I'm now using a $10 aquarium pump (up to 80 GPH gallons per hour), to pump water directly into the housing, which squirts a nice solid jet of water. The reason I kept the housing of this OriGlamp product is that it has nice mounting holes, which I will eventually use to mount onto my CNC machine's Z axis so the jet stream can follow along wherever the spindle goes. (In the video, I merely depict squirting the water at an aluminum rod from a fixed mounting point). Keep in mind the jet stream of liquid is messier than the mist/spray, although both can be messy... so I'm working on ways to collect the liquid so it doesn't splatter all over the CNC bed and possibly reach electronics.

I bought this to use as a portable coolant dispensor i could swap between the lathe, mill, and drill press in my little garage shop. This thing is really impressive. Getting all the hose fitting to conect to my little pancake compressor took a trip to the hardware store. I mounted it to a magnetic base i had laying around, so i can attach/deattach it and move it around the shop farile easily. It has 2 holes for mounting on the front corners, which isnt the best (takes long thin screws which meant i needed a wonky bracket to attach the magnet), but is workable POINT IS this thing absolutely revolutionized making parts in my little shop. Get a good coolant and watch stainless turn to butter. It is rather incredibly efficient. Ive been using it for a couple hours a day for several weeks and ive just gone through my first gallon. I mostly work in foodsafe plastics and stainless, this has eliminated nearly every issue i had with tools overheating or cutting badly. WIsh i had bought it sooner

Wow. Not sure why I didn't get this years ago. Cheap mist coolant atomizer that works pretty well, as far as I can tell. Idk how well it needs to work, but it does pretty well.

So far so good! I don't use the mist as much as I thought I would as it does get a little messy and swells up my mdf spoilboard. Being able to easily adjust, turn on/off the lubricant flow I can just use air for chip clearing and turn on the lubricant once in a while during cuts. Even with just using compressed air alone when cutting aluminium or acrylic it's a big help. I learned that having a VFD spindle and rigid machine isn't enough to reliably cut aluminum, gotta have that lube! The air and lubricant tubing that came with this kit was way too short for my 1000x1000 workbee but at this price I really can't complain! Would be nice to be able to select an option for longer tubing for an additional fee though as to reduce waste

Worked well initially but later coolant control screw failed. The screw cap fell off too.

I previously bought the cheaper one control mist coolers and struggled to get the coolant flow and air feed running properly. My mate bought one of these by mistake and asked me to help him set it up on his myford lathe. This model is so staggeringly better than the others around that I immediately ordered two for myself. Slightly dearer than some but night and day improvement. The cheaper ones only have one control screw that just doesn't work, in fact I had to pipe in a seperate tap to control the air properly, and they were still a fudge. These OriGlam ones have two controls, air and fluid, plus a non return valve in the fluid line that takes all the 'bounce' out of the line so the syphon effect works reliably. The air pressure needed is greatly reduced compared to the 'one control' types as well. I tapped one of the mounting holes with a 4mm thread and mounted 'silverline magnets' also available on Amazon. Now I can just clip them to any machine I am working at. Fantastic. Easy to plumb in with 8mm blue plastic pipe. Just push the pipe into the self sealing fittings. A slight push on the blue collars and the pipes can be easily removed to make packing away a doodle.

Für den Preis perfekt. Funktioniert super. Stellschrauben können gesichert werden und der Einstellbereich langt für mein Vorhaben aus. Nutze das Ding für eine mini CNC für Alu arbeiten mit Isopropanol.

It's kinda fiddly to get it to spray fluid. When it finally managed to produce droplets, the air flow was minimal. I need good air flow + fluid. But now I only use it for air.

Cet appareil, bien réglé, est sensé pulvériser, sous forme d'un brouillard de mini goutellettes, un lubrifiant facilitant la coupe, pour fraiseuse à métaux, tour à métaux, scie à métaux etc... L'avantage est qu'on utilise moins de lubrifiant qu'un jet liquide qui se répand partout, tout en conservant une lubrification efficace. Comment ? : Le petit tuyau transparent doit plonger dans un bidon de lubrifiant. L'autre entrée doit être raccordée à une pompe à air, idéalement un compresseur, car le débit d'air doit être suffisant. Ce débit d'air entraîne une dépression (effet venturi) qui va aspirer le lubrifiant et le projeter par la buse en laiton qui peut être réglée grâce à sa molette. Quel lubrifiant ? : Ne pas utiliser d'huile visqueuse. Le mieux est l'huile de coupe hydrosoluble DLUB. 5% de cette huile, 95% d'eau. Avec un bidon de 5 litres de cette huile, on peut faire 100 litres de liquide lubrifiant de coupe. Donc, se préparer un bidon vide et propre (genre bidon 5litres de lave-vitres auto) et faire le mélange 5% huile DLUB - 95% eau, pour avoir 5l d'un liquide d'aspect laiteux. Quel réglage possible ? : Cet appareil est un des rares appareils à avoir 3 réglages. 1) Le réglage de densité du brouillard par la molette de la buse de sortie en laiton 2) Le réglage du débit d'air venant du compresseur (ou de la pompe à air au pire, si elle a un bon débit) 3) Le réglage de la quantité de lubrifiant aspiré Cet appareil est très bien ! Dommage que le socle soit en aluminium. Cette base aurait été en acier magnétique, ça aurait été parfait. J'aurais pu le poser sur le chariot transversal du tour, ou de la faiseuse sans devoir percer mes machines. Au pire, il y a 2 trous de fixation pour le fixer sur une base magnétique. Conclusion : Bon appareil, bien pensé, de bonne qualité à un prix très raisonnable.

Impecável. Sem fugas, pulveriza na perfeição. Entrega dentro do prazo previsto.