Wolfcraft 4525404 Multi-Angle Drill Guide Attachment for 1/4In. & 3/8In. Drills,Silver

Good quality product which is effective and accurate

I liked this tool - used with a DeWalt cordless for making 120 holes in a piece of 18mm ply that need to be square.It did seem to need a bit of lubrication (certainly would advise that to make it last.It was a little wobbly and not perfectly square (c.f. a proper drill press).It does have numerous options for drill angles and drilling square and centrally into tubes and battens.Overall it is well worth the money and a great addition to the tool box. I would just like it to be a bit more solid.

Used this to drill through a steel bolt, needed to make sure I went dead straight. This did the job and is great if you don’t have a pillar dril/drill press, or can’t get a drill press into where you need to drill. The quality of this could be slightly better, I’d prefer metal fixings as opposed to the plastic ones, but I have to say it works great, very little runout in the Chuck, and I was able to drill my bolt hole very easily. Time will tell how it holds up to more use, but so far so good.

There is still a little bit of wobble in the item even when everything is tightened, so some holes might not be as accurate as I'd like.In addition, the chuck is slightly too small so slips everything you use it.

Its had limited use so and its worked well.

Like others, I removed one of the springs as it was too much push back and too squeaky to use otherwise.I got this one because I thought having the chuck moulded to the armature would make fore more square drilling, and I think I'm right. Also, it's easier to connect the chuck to your drill than the other Wolfcraft model where you connect it to the body of your drill and tighten it with two knobs. I hadn't considered that the mouth of the chuck only goes up to 10mm so that's important. The teeth of the chuck aren't tight, so sometimes it spins if you're not careful when tightening it.You get what you pay for basically, on balance I would probably get the other model as I wouldn't have chuck issues, and the other one's got a shop vac attachment which would be super useful.

I had high hopes but out of the box I could feel a considerable amount of play in the drill attachment spindle that holds the chuck. Undoing the circlip that holds it in place reveals no bearing at all, it's just metal on metal and the fit is quite poor with a fair bit of slop - there's no way anyone could get an accurate cut/centring that would hold its place.Might be fine for basic lightweight use but even the frame's uprights has considerable twisting wobble so I wouldn't trust it under medium or angled force especially with the extra weight of a drill attached to the top of the spindle which would only serve to cause further issues.Not worth the full money, not worth the £20 off offer price I got it for. A £9 plastic framed thing I got off ebay was considerably better in the chuck spindle area with a nice chuck and two quality tight bearings with no movement at all (the plastic frame of the ebay one though leaves something to be desired!)

Very good. Used within minutes of delivery. Only one gripe. It really needs somewhere to store the chuck key

Produto de excelente qualidade e de fácil manuseio. Atende aos requisitos para trabalhos de marcenaria quando furos como brocas de até 5/8" forem necessários.

I needed this specific type of tool to do a job. I didn't want to spend alot because it was a one-time project. The tool is light-weight but worked well and I am sure other less than professional carpenters would get use out of it and be pleased with it.

Funciona muy bien, el material es bueno, recomiendo que tengas dos taladros uno para que lo instales en este soporte y otro para que hagas otros trabajos, usar el mismo taladro para varios trabajos es un poco tardado usar el mismo, estar quitando y colocando el mismo taladro pierdes tiempo.

too much plastic in the key parts and too much motion in the assembly. this isn't very sturdy and could be made a better by using more metal parts to adjust the angle of the drill.

Helt ok, lite fippligt att få till vinklarna helt rätt. Men ångrar inte köpet.