Oregon 4.0 x 300mm Mulching Brush Cutter Blade, 2 Tooth Shredder Strimmer Blade for Thick, High & Dense Vegetation, Fits All Brushcutters Including Stihl, Echo, Husqvarna, Echo & More (295505-0)

Used this to rip through a lot of bramble bushes. Made short work of it, reduces them to nothing. So works really well and highly recommend.

Brilliant brush cutting blade that also mulches as you go. Cuts straight through saplings.

I have this on my Stihl FS 131, and works well on my blackberry and bamboo that has taken over the back portion of my lot. It mulches well, which was what I was looking for and does not spray debris upwards like some of my other blades. A few years back I bought some Airecut blades, and found them phenomenal at chopping and mulching but I would be covered in brush shrapnel. For some cuts I still prefer the Airecut as it does not allow long grass to wrap and wind into the spindle, but for out and out brutal mulching this Oregon blade is the tool. My only concern is that I have noticed my Stihl takes a moment to spool up speed, and sometimes there is hesitation. I have weighed the Airecut at 500 gm and the Oregon comes in at a heftier 580 gm. So definitely a heavier blade. I have ordered in the 3 mm blades and will see if it will reduce the wear and tear on my Stihl's clutch compared with the 4 mm. Update: Received the 3mm blades, and significantly lighter. The 3 mm blade weighs in at 430 gm. On my Stihl FS 131, this 3 mm revs very quickly, none of the hesitation that was noticeable with the 4 mm and none of the occasional clutch chatter. Both blades are identical in dimensions other than the thickness. After a few months of using the 3 mm and the 4 mm blade, I must say that both blades have it's place. The 3 mm is a lighter blade, and find it a bit quicker for maneuvering. It spools very quickly and I find it less taxing on the arms when I crank the high branches. On the other hand, doing the ground mulching, the branches and debris can sometimes stall the blade. The 4 mm is a beast, and with it just cranked wide open it seems nothing will stop it, there is so much inertia from the blade in motion. I have noticed that the metal on both the 3 and the 4mm needs to be sharpened often, almost after every hour of use. I do grind a lot of 1/2 to 3/4 inch branches. I do have a dremel tool and sharpening is fairly quick. Some thoughts after 4 years of using these blades: 1. If your budget allows get the biggest engine you can to maximize the potential of these blades. 2. I have destroyed a 15 year old Toro 27cc crankshaft with the 3mm blade, seized up a clutch on a 5 year old 29cc Troybilt. Stick with good quality machines such as Stihl, Echos, etc. 3. Sharpen the blade often to get the most benefit with cutting and mulching. When the blade is dull it does seem to add extra load on the engine. 4. Put a cover over the blade and this allows for a better mulch while also preventing debris from flying into your face.

This is a very good shredder blade, very strong and durable. The only downside is the reducer ring. I bought for a Stihl fs260, but hit a hard object and that put an end to the reducer ring. Still works on a lidl strimmer though. So I would say best for a machine with a 25.4 bore.

What an amazing bolt on to my strimmer. We have an allotment plot where Brambles are the worst, constantly encroaching on to our plot. This thing spun up to speed on the strimmer and demolished an area of 25ft by 10ft in size in about 15 mins. It shredded the new green plant life and made short work the dead very dried out stuff beneath it. Very impressed by this tool. I did sharpen mine before first use to get the paint off the cutting blades. Highly reccommend. Advice though, make sure you buy the right size for your strimmer, I know you can get diff lengths of this tool, it is a little heavy and takes a few seconds to spin up to speed. I dont know what our strimmer is but its mounted like a backpack for me so carries a decent power.

Excellent blade for dealing with brambles and brush like nettles, dried bracken, young saplings etc. Beneficial to keep the blade sharp (I used a flapper disc so not to remove too much metal) and you'll work out the best way to use the blade, like twisiting the strimmer slightly on the angle when moving side to side or more of a vertical movement for the taller stuff, then running the blade over any large debris laying on the ground. I found that long thick grass can wrap around the wings of the blade and cause it to vibrate due to the weight imbalance but as soon as the blade makes contact with some brush the issue gets resolved. For what it cost, the time it saves and the end result is seriously impressive; wish I bought one years ago. Bear in mind that depending on what your cutting it can throw out some lumpy debris so protect your legs. Not ideal but I removed the guard to reduce the snagging on the brambles so if you do the same make sure you're protected.

Good value Good quality does the job very well

Fitted nicely, on my Stihl FS550 it is a bit more wiggly/vibration than I would like which means I can only use it for about 30mins at a time. I might need to have a go and adjust it or fit another flat washer or something, but it is a bit frustrating. I'm not great with rotary mechanics, so it might be me. I tightened it pretty well with socket set and rubber mallet, so don't think it is slipping. The aluminium insert is fitted and is flat, but could be riding up slightly under the hollow Stihl retaining washer - hence thinking about needing a flat bit to keep it down - just a guess though.

Extremely impressive solid metal bar weed-wacker. Easily takes down thumb thick woody shrubs like Lonicera and Box Elder. Easily attached to my weed-wacker pole, so compatible (just check your unit before). Bbe very careful because this thing will easily take your leg, lol; treat it with respect, lol. Very powerful for clearing woody brush, less ideal for grass, but can cut tall grass if needed. Used it for 2 seasons know and it's still going strong, the red paint on the cutting edge has worn, but it still works perfectly. This is the real deal.

Nice blade

ch habe mir dieses Oregon Universal 2-Zahn-Mulchmesser (4,0 x 300 mm) als Dickichtmesser für meine Motorsense geholt, um eine völlig überwucherte Fläche mit dicken, verholzten Brombeersträuchern freizumachen. Was soll ich sagen? Das Messer ist eine absolute Wucht! Die Materialstärke von 4 mm macht das Messer extrem robust und verwindungssteif. Wo normale Fadenköpfe oder einfache Messer kläglich versagen oder sich verfangen, schreddert dieses Mulchmesser das dornige Dickicht einfach eiskalt kurz und klein. Die Brombeerranken werden nicht nur abgeschnitten, sondern durch die spezielle Form direkt ordentlich gehäckselt, sodass man das Schnittgut danach super kompostieren oder liegen lassen kann. Es passt perfekt auf die gängigen Aufnahmen und läuft absolut vibrationsarm, sofern die Motorsense genug Power mitbringt. Wer hartnäckiges Gestrüpp und Brombeeren im Garten bekämpfen muss, macht mit dieser Profi-Qualität von Oregon absolut alles richtig. Klare 5 Sterne und eine fette Kaufempfehlung!

j'ai acheter cette lame car j'avais des ronces plein le jardin. La lame est grande et fort épaisse. en utilisant la débroussailleuse de haut en bas, ca broie incroyablement bien. attention que la lame fait un certain poids, l'inertie de celle-ci est est donc importante.

de detaljer som gör att kniven ska passa många trimrar saknas. enda detajen är en bricka fasttejpad på kniven