Liquid Ultra Cooling Kit with 1 x Cleaning Set

I will admit, it was only after so many tests showed just how positive the results were that I impulsively bought this as I needed a new thermal paste and tomshardware guide and other such sites showed just how much better the results can be Hands up, I was impulsive and thought this is the stuff for me.. it was only after it was delivered did I start to read how it can be very corrosive to aluminium and how reviews stating they didn't feel safe using it compared to a typical thermal compound did I start to have concerns. So after much googling to ensure no aluminium was present I took the chip out just to be safe and the brushes included with this were excellent for application, and made it super easy.. It also made sure that any of the little bubbles that can appear are quickly rectified and spread out. I would whole heartedly recommend this, drop in temps is significant when you think this is only a paste.. application is simple and I am a fond believer if i can do this then any semi competent individual will have zero issues. Just make sure the cooler is not aluminium. my i7-4790k is now running @ 60c under full load on prime 95 which is a significant 4-5c drop on previous results.. very happy

I used the liquid metal between die and heatspreader in my de-lidded i7 and between heatspreader and Macho series air cooler. Before this change my CPU would run around 80 degrees when overclocked. In the same case and with the same overclock it now runs at 60-65 or below. Astonishing!!! Never would have thought it makes that much difference. By the way, the CPU is a 4790k, so it already had the "updated" heat transfer material from Intel....still the change to this made such a difference. Practical tip: Best apply with a Q-Tip instead of the supplied brush. With that you can "massage" a tiny amount into whatever surface you are using it on without any spills. The syringe was enough for the de-lid project, the cooler itself and my notebook CPU and GPU (which now also run 15 degrees Celsius cooler). After that it was exhausted, while still looking to be quite full. I had to find out though that the remaining silver stuff was just some solid powder, no liquid. Not sure what or why...

Great thermal compound. The package comprises the thermal compound, two application brushes and a cleaning kit (cleaning tissues and metal grinding pad). I used it to improve the thermal transfer efficiency between my CPU, GPUs and their respective copper water-blocks and was impressed by the numbers. Additionally, I have used it for air cooling with a Cooler Master Hyper 212 Evo , also with good temperatures. For the best results, only apply the minimum required to thinly cover the surface of your processor. Great for overclocking a CPU, provided a quality third-party (non-stock) cooling solution is also used. Recommended. WARNING : NOT TO USED WITH ALUMINIUM This stuff corrodes aluminium very quickly. So make sure it doesn't come in to contact with any aluminium, especially on your heatsink (if applicable). If your heatsink gets eaten then your CPU will die!

This stuff really works! I had upgraded the processor in my laptop, but the added temp meant it kept crashing and freezing when it thought about things to much. After reading a few reviews I opted for liquid ultra. It dramatically dropped the temps in my laptop and now it's as fast as ever... No crashing or hanging. Thank you!

6 months down the line, applied to 290x with aftermarket cooler, good consistent temps, doesn't appear to be subject to "pumping" effect. Will leave for another 6 months and consider reapplying. To clarify, you get LOADS of compound, enough for many applications when applied correctly i.e sparingly. Add a small amount, spread with supplied brush, if you haven't used enough, you can always add a drop more. Don't slather it on.

I must have tried 10 different Thermal pastes in my builds but avoided this one because of the price, with my last overclock the temperatures were getting up to 85+ degrees C, my water cooling just wasn't enough with normal thermal paste so I thought the only thing I hadn't tried was this. I was a little disappointed with the amount that comes in a syringe only enough for 1 application with other pastes you get several times the amount. Well when I saw the the results the cost and amount you get became irrelevant this stuff is brilliant I can't get temps over 45 degrees C no matter what test I do, I would have never thought a thermal paste could make this much difference. Thanks Coollaborotory brilliant stuff.

great stuff but make sure you know your a 100 % sure you know what your doing before buying it.

I used this with a deluded i7 3770k as I looked it up as giving best performance which it did and does. My 3770k had very poor thermal paste under the IHS which was too thin and had dried up. Overclocked @4.6ghz 1.42v (my cpus max overclock) my cpu was throttling under load to 105oC and to the stock frequency of 3.7ghz. My cooler is a single fan corsair h60 which is an early and basic 120mm AIO cooler but it didn't get warm when the cpu was hot which is usually a sign of bad thermal. After dellidding with a tool not the silly razor method I applied liquid ultra and got a max temp of 75oC. I had to reapply the liquid ultra 5 months later as I was getting temps close to 90oC which is why this product only gets 3 stars. Hopefully with the next CPU refresh intel will solder the IHS and people will stop buying 140mm, 240mm, and 360mm AIOs as current coolers are overkill.

Il prodotto è spedito immediatamente ed arriva dopo circa una settimana e mezzo , corrisponde esattamente alla descrizione comprende il metallo liquido ( siccome ne va steso poco è sufficiente per più applicazioni ) panno abrasivo per pulire a fondo le superfici interessate , carta imbevuta di alcool isopropilico sempre per pulire. Personalmente ho utilizzato il metallo liquido per stenderlo tra ihs e die di un i7 4770k , con la procedura sono passato da 83 gradi ( 4.2 ghz e 1.18 volt ) a 73 gradi ( 4.4 ghz e 1.24 volt ). Il prodotto è enormemente migliore delle tradizionali paste termiche nel trasferimento del calore , ovviamente però bisogna ricordare che conduce la corrente e perciò si deve assolutamente evitare che vada a finire su connettori, Pin , contatti e quant'altro , ad esempio se si vuole mettere tra ihs e die è bene prima isolare i contatti sotto l'ihs con smalto per unghie o altro composto adatto . Si può stendere anche tra cpu e dissipatore facendo sempre attenzione a stenderne una piccola quantità ( su quest'ultimo punto fate attenzione , nel mio caso dopo averlo steso tra cpu e dissipatore ( un corsair h60 ) il metallo liquido non si è "spalmato bene " ( forse un mio errore di stesura ) e perciò il contatto tra le due superfici era limitato a soltanto piccoli punti più sporgenti di metallo che si comportava quasi come fosse solido e non liquido , cioè ha portato ad avere temperature oltre 100 gradi con conseguente trottling termico della cpu ( ovvero cala drasticamente l'utilizzo per non fondere ) , ho risolto tale inconveniente sostituendo il metallo liquido con pasta termica tradizionale tra cpu e dissipatore ma lasciando il metallo liquido solo tra ihs e die, ( Ovviamente parlo di cpu deliddata anche detta scoperchiata ), infatti tra ihs e die non ho riscontrato tale problema , forse perché vi ho applicato una maggiore pressione durante il montaggio cosa che forse ha permesso la giusta adesione delle due superfici .

Please note I've used F and C temperatures a lot, as we use F here but computers default to C readings unless you change it. Delidded 4790k finally has it's heat-issue since day 1 fixed with this product. Bought a delid kit 3 months ago to delid the chip, which worked, but Zalman ZM-stage 1 didn't cut it for this hotbox processor. The computer was disassembled quickly and the cpu removed. I removed all the old gunk and used some alchohol on the processor and lid, and also the heatsink contact surface to remove oils etc. Painted the smallest amount possible ontop the processor die itself, and re-assembled the processor package itself. I then removed the lid for a second to see that NONE of the material escaped where it belonged. For those that don't know, intel doesn't solder the LID of the cpu to the chip, for mainstream Z or B-chipsets from 3xxx series and higher. I placed the processor back in the pc (which was upright, I used a plastic fork leaning on my GFX card, to hold up my CPU retention plate to insert my cpu easier with two hands). I then painted on to the heatsink some of this good stuff - just enough to barely cover the surface, it's base is copper, this is NOT made for aluminum and will harm it. Most enthusiast heatsinks are copper or nickel-plated copper. Check your documentation to be sure. The lid of the CPU on an intel chip (if you're delidding), is nickel-plated copper, NOT aluminum, just to make this clear. I let the processor sit for 10~15 minutes before re-installing the cpu & applying material to between the heatsink and cpu itself. I waited so that the lid would not fall back off of the cpu when I was installing it. Maybe cover or remove your video card in-case it does. I replaced the heatsink & bolted it slowly back into place, after everything was dusted a bit, since now is a good time to do it. 4.0GHZ speeds at stock voltage showed a TWENTY DEGREE DROP (both while delidded), compared to ZALMAN ZM stage 1, under load. 4.4GHZ speeds compared also resulted in a 20C drop. It was about 30~32F or something close to that at this clockspeed under load. I checked that everything was A-OK in BIOS and monitor temps for a few moments, everything checks out nicely. The stock heatsink would throttle in every multi-core game. This is with a non-delidded processor. Stock heatsink is useless - USELESS. Phanteks TCP14E 140mm dual-fan dual-tower cooler (red model) was used for the temps listed above, and is a good air-cooler. Using said cooler, I could hold my turbo speed but it would still get very close to around 80C~84C under load (not delidded, zalman paste) Delidding and using Zalman paste actually raised temps by 3~8 degrees F (2~4C). Possibly put a touch too much on when I did it. Now for this product (clarification, used all air cooling, no liquid cooling here) Delidding and using THIS PRODUCT dropped temps substantially, from the first delid attempt that I had previously tried. Idle load at 4ghz was 90~105F (not C!), loading brought these temps to around 160F on highest core reading (70~71C). Idle load at 4.4 ghz turbo (ALL cores) brought this to around 100~113F idle, and no higher than 162F under load (72C). Full load running fallout 4 heavily modded and not really gpu-constrained too much at 1920x1080 did not exceed the temps above. I used default 1.0925V for 4ghz, and 1.25V at 4.4ghz, for the tests above. Hyper-threading and virtualization features are ENABLED. My computer is cooler, quieter, and my cooler and other fans don't have to work nearly as hard now, as heat transfer is much more efficient. I have enough product left over for four uses including what is used right after delidding this processor. While you may use this product on any cpu, keep it off your circut boards or you WILL have issues and your machine may not boot. DO NOT attempt to delid processors before 3xxx series on intel systems, or x79/x99-based systems, as they're all soldered. DO NOT attempt to delid any AMD processors or you will break the processor. Delidding is a tactic used by folks wanting to make the heat-transfer of heat inside the CPU to the cooling unit more efficient, to help squeeze every last bit of power out of the system or just make it cooler/more stable/quieter. You should expect a 10C drop normally when delidding and using this, and atleast a 5~8C difference between this and the leading non-metallic products like I mentioned before. Your mileage may vary, but if you have a similar CPU, expect about this. The warmer this chip gets (70C and above), the more likely instability will occur, you need to keep this CPU cool. When applying this product, apply it to one contact surface, not both (e.g. put it on the cpu surface or the bottom of the cooler, NOT both). Bare-bones Instructions come in German, English, and French on the package itself, the website has more available for more detail. In the package is: Two brushes, a cleaning pad, a scrubbing pad to remove old paste, the material itself. A grain of rice size is a good start between the cpu top and the bottom of the heatsink. Don't use too much here, as too much is better than not enough. A pea size blob may be too much. A grain of rice or LESS for the inside of the cpu if you delid. Keep in mind delidding knocks out your standard CPU warranty. Alchohol will help you remove this stuff if it gets where it should not, please be very careful with it & keep fingers OFF the area you wish to apply this, or it WILL NOT stick. That bacon sandwich and french fries will have to wait for later as did mine. If you use this with a RYZEN cpu please be aware that temps may read (since day 1) 20C higher than they really are, this is normal, and is not this product, please consult power-user / hardware forums for the skinny on that. It's a built-in safety margin, for what it's worth. When I say 'paste' 'material' or something similar, I mean the product you get in this package. Sorry if this doesn't read well, please excuse that I wanted to include as much needed info as possible. --Cheers! Feel free to comment/like if this is or isn't up-to-snuff, I can clarify and modify this if needed. Best wishes!

Soyez bien sûrs d'isoler le reste de la carte mère si vous appliquez ça sur des CPU/GPU de laptop. Sinon c'est vraiment génial, on peut presque passer à du refroidissement passif. Je recommande!

Good.

This is the best thermal interface material you can buy, thermal transmission wise. I use it on delidded CPUs and GPUs. Read the instructions and know that this TIM is NOT to be used on aluminum. It will EAT aluminum. Be aware that this TIM is also conductive, so keep it away from exposed circuitry. You also need very little of it applied. It is a liquid, and will drip off the surface onto other components if you apply too much. Use the included spreader brush and start with a very small amount, adding more only as you need it. Also, the two syringes that I received did not come with needle points on them. As a result, the liquid metal pooled in the cap of the first syringe during transport, and when I removed it, the liquid metal dripped out onto my work bench. Approximately 5 ml of it. MemoryC was kind enough to send me another syringe. I am not sure why the Coollaboratory products I received didn't come with needle points on the syringes, as seen in video product reviews by others, so be careful when removing the syringe cap for the first time. Store the product with the syringe open end upwards to prevent the liquid metal from pooling in the cap due to gravity.