Powerbuilt 2 Ton UniJack Combination Hydraulic Bottle Jack / Jackstand in 1 Unit, Compact, Portable, Wide Base, for Unibody Sedans, CUVs, SUVs, Cars, - 620470

As my Audi Q3 is a unibody vehicle, I jack it up by its pinch welds. Unfortunately, the pinch weld seems to be only about 6" long. As such, if I use it as a jack point, I cannot fit a jack stand at that spot. That being the case, I had to do recent wheel work relying solely on the provided OEM scissors jack and sometimes on my 2.5 ton floor jack. While searching for alternative safety measures, I came across this Powerbuilt All-in-1 Unijack bottle jack with built-in jack stand. Not only does this concept provide the safety I am looking for but it is actually much easier to use and more compact. * Note - Due to the way this is built, it will not be useable for a low clearance vehicle. The lift range is 8 5/8 - 18 3/6. The lift head is adjustable to accommodate higher lift vehicles. It does not come with a rubber pad so contact would be metal to metal, (I added a rubber pad to prevent any damaged to the pinch weld). As tested, my SUV with a curb weight of ~3900 lbs. was raised without any issue. I definitely recommend this for anyone whose vehicle is of a suitable height.

I regret buying just one, used on my durango 2017, it fits perfect on the lift points, I but just one just to see if it fits, it had a good discount. After I used I was about to order the second one but it already went up. Hoint to wait to buy my second one

This jack is a great idea. But in the real world it doesn't make sense to use it. It says it can lift from 8.25" - 19". That is technically correct, but the truth is that it only lifts about 6" at a time. So to lift over about 6", you have seat the jack, pump it up 6" to the end of stroke, put a jack stand under the car(you know, that part you were trying to eliminate), lower the jack all the way down, extend the extension, then jack it up again. Then you are set. Until you want to lower the vehicle. Great idea, poor execution.

I bought these because I need to work on the flex plate of my driveshaft, which will require removing the entire shaft. My vehicle doesn't have any places to set jacks or stands other than these square blocks underneath next to each tire. Therefore, I wouldn't really be able to jack it up and then also place it on stands. This product eliminates that issue, BUT for my vehicle, it's about 1 inch below the height of this jack, which means it won't work for me outright. However, I can use my ramps in the front, which will raise the backside enough to slide these into place, so no issues at all. These are a well engineered product that I will feel safe trusting to keep my car steady while working underneath. Just make sure to check your height profiles because these do sit fairly high from the start.

This works almost perfectly to lift my 2022 Bronco Wildtrak. Seats on the rear axle tube just fine, and lifts the front from the frame without any issues but it is only barely high enough to lift the front wheel off the ground from the frame. I'd rather have a bit more travel distance to lift the front so I might grab the larger version in the future.

Very happy with my purchase I bought another one

Works great! Easy to use.

This is for the 2 ton Powerbuilt Unijack. Mechanically, both jacks I purchased seem to work fine and came undamaged. It's nice to have a jack that has a latch system to hold a load built in. On both of the jacks though, the hex head screw on the flat piece on top of the ram was not flush with the top piece so a flat piece of metal will rock some and a significant amount of weight will be only on a small part of the top piece, the screw head. I ground some off of the top of the hex head screws to lower them. After this modification there was no issue but I should not have to modify them. The handle included with the jacks is too short and fits with too much slop in the jack! When inserted in the jack, it extends only one foot! It was no wonder why it took so much effort to lift only approximately 1/2 the rated weight. The total handle length is 14 inches while another jack I have has an extendable handle that can extend to about 23 3/4 inches which is almost one foot longer than the handle included with the Unijack. I do not understand how any normal person could use the jack to lift the max rated weight with a handle that only sticks out of the jack 1 foot. I emailed Powerbuilt about the handle being way too short twice, first being over two weeks ago and and there has been no response. It looks like I will have to try to purchase a handle with the proper length or have one made. I understand, after calling Powerbuilt, that many negative reviews are a result of improper operation, including removing the valve at the base of the jack to lower it when the ratcheting mechanism is preventing it from lowering. When the valve is unscrewed significantly or completely, of course oil will leak out! People need to fully understand the jack's operation.

Ich bin mit dem Powerbuilt 620470 Unijack - 1814 kg Kapazität sehr zufrieden. Sehr gutes Gadget für SUVS wie Mercedes GLE, GLC oder GLS bzw BMW X3, X5 oder X7. Ich selbst habe es für meinen Mercedes GLE und Mercedes 123er verwendet. Man kann schnell und sicher am Auto arbeiten, egal ob Reifen-, Ölwechsel oder andere Arbeiten am/unterm Auto. Man spart sich das lästige Anheben mit dem Wagenhaber und anschließendem Absichern mit dem Unterstellock, da dieses Gadget beides (Wagenheber und Unterstellbock) in einem anbietet. Ich kann es nur weiter empfehlen.

Needed a jack that would lift up my Kona and this works perfectly. My other floor jacks just didn't have the height needed. My only issue, and this is my fault that I didn't notice, is that this jack is about a half inch to tall to fit under my car without having to use another floor jack to lift it up to get this jack under it. Not the end of the world but a slight inconvenience. Really like the built in jack stand also.

El un buen producto, funcional y la adicion de torre de seguridad con autobloqueo funciona bien y brinda una buena altura para levantar en menos movimientos de bombeo. Recomendable medir previamente la altura al piso restando el grosor de la llanta para saber si entrara bajo el vehículo. Este es para vehiculos con un buen despeje del suelo.

Awesome tool. Im sure i will get many uses out of it. Disappointed that it will not fit under my minivan though.

Muy buen producto me gustó mucho práctico y seguro