Motip M04062 Aerosol Spray Paint, 400 Ml

I'm very new to spray painting but it gives a great colour. It sprayed really well. Layer thickness was good so no need for crazy amounts of coats. Can still feels full so I feel like this can will last me a LONG time at least for me who doesn't spray paint often so good value for money. Once fully dry it's not too strong so easy to sand but not too weak that you can easily mess it up.

This stuff is a must-have for anyone doing FDM 3D printing. It's super easy to use and dries fast if you apply a few light coats. It leaves a mostly smooth finish with a slight bumpiness, which I actually like—it makes it easy to see where I’ve sanded and where I still need to work. I usually sand it with 1000 grit paper, sometimes wet sanding to keep the dust down. It takes about half a can to fully smooth out a 3D-printed cosplay helmet, and it really cuts down on post-processing time. Durability has been great so far—no issues with flaking or chipping. Just follow up with some primer, and it’s ready for paint. Definitely a staple in my 3D printing workflow.

This stuff is a must have for FDM 3d printing

I use this to help level and finish 3D prints. The filler/primer does a great job of covering up minor imperfections in your prints. The level of finish you get will depend on time and coats, but a 'paint, 'sand', 'paint again' approach is a good way to go. It sands really easily, and you can lay it on pretty thick if you want to as there is a self-levelling behaviour to it. Dries to sandable pretty quickly.

I've purchased this 5 times, when i first started using it the price was great now it's popularity seems to of pushed up it's price. Perfect for getting a smooth even finish however if you follow the instructions that is. Light coats only as the heavier you go the longer you will wait for it to cure enough for wet sanding and gum up the sandpaper in the process wasting time. I start off as always sanding with 120grit then 240 wet sand before applying this product only a light coat and then will wet sand at 400grit before applying another coat 45mins later usually two to three coats are enough to fill in any scratches from sanding and light layer lines. If you think this will eliminate sanding it wont :) But it does help reduce the amount of time spent doing that drastically.

I do a lot of 3D printing projects and this is invaluable for making a professional, well made prop. It fills in any imperfects or cracks and dries very quickly, on top of that it makes your paint stick like nobody's business. This is my go to product for painting and filling my prints as it can even be sanded for an even smoother end result. I recently used it on a big project to make a full set of mandalorian armour for my kid. It came out perfect, one happy child!

Tried this spray on some new prints, layer lines are 0.3mm high so I didn’t expect results fast. On flat surfaces 2 coats half an hour apart and 2 hours to dry have a perfectly smooth to touch finish (with 240 grit paper). Coverage was good, but only use on fine lines or scratches, use other fillers like wood filler to fill in the roughest areas or lager layer lines then go over with this.

Bought this after seeing a Youtube vid. Great for getting rid of layer lines in prints and making them feel smooth. Layer lines no matter how small seem to get dirty in them over time, on prints that are handled frequently. I applied two thick coats, sanded with 400 grit and then sprayed with gloss. This made my top layer feel like an injection molded part, not 3D printed. If you have layers of above 1mm you will need several coats and more rubbing down. Only downside is that you should use it outdoors. I used an an extension and even though I put newspaper down and sprayed in the middle of the floor, it seems to form a dust mist in the air that gets all over everything a foot up from the floor, including my shoes. Not to be used in the house again as cleanup is a nightmare. Unfortunately winter is here so it's on the shelf for now until I can use it in the shed. Nearly marked down one star because of this, but perhaps that's a little unfair.

Consigliato un prodotto molto buono copre già alla prima mano

Ik gebruik deze twee in één bij het 3D printen. Alle prints op een FDM printer worden met dit product behandeld. De putty doet de printlijnen verdwijnen en de primer zorgt ervoor dat de print ook dadelijk in een kleur kan worden gezet. De beste resultaten bekom je door meerdere lagen aan te brengen en daartussen een lichte schuurbeurt te geven. Enig nadeel? Het is vrij prijzig maar het is dan ook een goed product.

Bin mega zufrieden damit. Hab gekauft für meine 3D Druck Arbeit. Füllt sehr gut und lässt super glatt schleifen! Gerne wieder!

Esta masilla en spray es muy finita y cubre bien las líneas de capa de las impresiones 3D, para que con un poco de lija esté perfecta para imprimar y pintar. Muy recomendable.

Parfait pour le lissage des impressions 3D. Je le recommande vivement.