Epoxy Resin 2 Gallon Kit, High-Performance Table Top Epoxy Resin, Self-Leveling, Minimal Bubbles, Clear, Glossy, UV Resistant, Perfect for Table Tops, Crafts. DIY & Pro Number 1 Choice

I must admit, I was pretty sus when I ordered this. I'm a wood turner and everybody always tells me, "ALUMILITE CLEAR SLOW" is the ONLY epoxy for turners. Well, I'll never buy ALUMILITE again. At 25% of the cost vs. Alumilute, that might be enough to change brands. But there is no "might be" here, this stuff is incredible. First off, it's easy. 1:1 mix and you're set. Cups included just in case you ran out. It mixes like a champ. Smooth, not too thick and air bubbles float their way out in a minute or two. The long working time is great, especially if you're using more than 1 color. Plenty of time to get everything prepped and make your pour without everything turning into a weird blob. Give it 2 or 3 days to cure. Patience. Don't whine, go do some other junk and come back later. It sets hard, like brick wall hard. I was little worried it was going to be brittle but when I started turning it, I was blown away. I used a bottle stopper mold and poured a 2 x 2 x 2 block. I used a carbide square roughing tool to start and finished with a round carbide. I did not cut the corners before turning. I chucked it, spun it at 2k, and dug in. This stuff turns like butter! It is incredible, not brittle at all, ZERO bubbles, great coloring throughout (used mica powder) and an absolute pleasure to work with. I will never buy another brand again! Can't wait to make more stuff with this!

This is the only brand of resin I will use. It was recommended to me by a fellow resin artist and I have never used anything else since.It is a thicker resin and low odor (but I always wear a mask regardless.) It comes out crystal clear - no yellowing, no fogginess. Also mixes well with additions like flowers, glitter, stones, mica powder, and liquid pigments. I have used all these with it with great success.It takes longer than some other resins to fully cure and set but it is well worth the wait for the beautiful result. My pieces usually take 48 hours or more to fully cure using a heated curing machine for several hours and then letting them set in a cooler environment after.I mix for AT LEAST 6 full minutes if not longer using a silicone spatula. It does not cure fast so you have plenty of time to work on your projects.Everyone who sees my resin products always asks me what brand I use because the finish looks just like glass!

This is some of the best epoxy I've used... It is very hard and makes an excellent floor surface.. SMJ 25

I bought this epoxy to strengthen the basically hollow transom plate for my troll motor tiller. I also bought this cut fiberglass pieces to strengthen it even more: ihttps://www.amazon.com/dp/B08Q84CS3P?ref=ppx_yo2ov_dt_b_fed_asin_title. Mixed the hardener and resin really good, then added what I thought would be more than enough of the fiberglass. Well,....it wasn't nearly enough, because all the fiberglass pieces sank to the bottom of the pour. So, if you want to add this fiberglass, you might want to add two to three times MORE than you think is enough. This stuff is so CLEAR, it's like glass; you can see all those fiberglass pieces on the bottom of the pour. Oh well, at least the bottom is going to be REALLY strong!!! And, it takes an hour or more to start setting up, which gives a lot of time to get out the heat gun and get rid of any bubbles (very, very few, if any!). Great stuff!!!

Use it all the time.

I’ve tried other tabletop resins and this one is by far the best I’ve tried. Very few bubbles, good workable time before curing, cures crystal clear for me every time. I have experienced a few micro bubbles here and there, but that was not due to the resin, it was due to the temperature before mixing. I have also since started using a vacuum pump & chamber with each different resin I’ve tried, this one seems to be the only one that cures with minimal micro bubbles of any. I use this for sealing my projects as well as flood coats, and non deep pour molds. If you plan to use this in a deeper mold, just do it in layers and you’ll be set. Cure time has been satisfactory in both warm and cold temperatures. I highly recommend Beast Bond epoxy resin. Repeat customer, price has been reasonable per volume, but I do try to purchase when there are coupons available.

Speedy delivery and I like the quality, the clarity and mixing cups and other things that come with it. Compared to other products I've used, this is the best. Thank you!

Says 24-48 hours to cure. It can take a bit longer but once it sets it is a good product. I would not use on anything high traffic like a kitchen counter without a durable top coat. For clarity or coloring it does really well.