SANAAA Silicone Mold Making Kit-Liquid Translucent Silicone Rubber for Resin Molds,Silicone Molds DIY Manual Making-Mixing Ratio 1:1 (500g)

My first time to do molding, Sanaaa made it easy for beginners like me, Just followed the instructions 1 to 1 by a gram weighing scale, Mold Settled the next day quickly as I expected into a perfect form as I want it to be, Just wished I had more of it, definitely will purchase more for my Projects. Excellent Product....

After a mould using both bottles at ones it didn't harden. 5 days later and it still didn't harden. Complete waste of money. To be noted that it is a closed mold, without air access.... could be that it doesn't dry without air. Anyhow, just a waste of money and lot of mess to clean.

good but its hard

Although I did sealed well around the object, it still leaked. The mould was very sticky slime like texture , it did not dry well from the inside & was so heavy & thick from the outside Big failure, it is expensive to throw this amount of money in the garbage

Esta silicona es 15A, la mezclé con 2kg de otra de 10A de otra marca porque necesitaba 3kg, el producto final es un molde grande y su resistencia es buena, el patrón es de resina epóxica, observé que tardó como 48 hrs en secarse en las partes más escondidas. Quedé satisfecho con el resultado hasta el momento, pero todavía no uso el molde, regresaré a actualizar la opinión cuando lo haya usado varias veces (piezas grandes de resina epóxica). TIP: Descarten Aprox. 20gr del envase y 35gr de material que se queda adherido a cada botella, esto debería ser un dato que proporcione el proveedor en cada tipo de envase :-(

super facile pour un moulage très précis

Ich bin sehr enttäuscht von dem Produkt. Nach 3 Versuchen war nur die Hälfte ausgehärtet. Der Rest fließt. Es handelt sich um einen unzuverlässigen Verkäufer und ich glaube, dass es mit etwas anderem vermischt ist, um mehr Volumen zu erzielen.nach zwei Tagen blieb es so

大型プラスチック部品（200×300mmぐらい）の型取り（キャスト）用に等重量（小数点以下一桁まで一致）で混ぜて型に流し込んで使いました 泡切れもよく、硬化時間も23℃室温で１時間かからないくらい、よく硬化させたいならもう2、3時間おくと良いかな 自分は結果１日くらい放置になりましたが 硬化後のかたさは15Aなので耳たぶぐらいのを想像してたけど、固めの牛乳寒天ぐらいありそう かなり伸縮性のある強度もあるシリコンゴムになりました 液はよく撹拌して混ざりきると一旦粘度が下がるのでそこまでは撹拌しました 液の粘度はシャバシャバではなくトローっとしてるけど、流れは良いと思います 自分の場合硬化までに気泡は全てなくなりました 初めてでしたが、とても使い勝手のよいシリコンです 足りなかったので計2リットル買い足しました

This is a good way to produce small molds of your favorite baked polymer clay, creations. Works easily for production of fast copies of your crafts, so you can make earrings, buttons, pendants, and small bas relief items to add to your shadow box, or perhaps you can make custom epoxy resin cabinet knobs. This product is firm enough to make larger two part molds, the cost is on the high side but many mold making products are expensive. This products mixed easy, what I do is compare the level of the two bottles after each pour, and make sure the ratio is correct that way. I was using one of my silicon cups for this, and after using their lines on the cup the levels were not the same, so be aware that your measuring tools may be flawed, and double check. I prefer to mix by weight actually, but did not do that in this case because often times when I do that, I end up with one of the bottles having significant product remaining. Can the mfg get this right for us? This product set up quickly but had a very generous working time. Unmolding the next morning the reliefs are very nice. This product degasses on it's own. Once poured, I did not disturb the project at all and made sure the items were still in place and had not lifted or drifted. You can add a bit of double stick tape to secure the item to the base, in the case of clays, and even resin or plastic items being cast. You can make molds of anything. Shells can lift so securing them is a good idea. 5 stars, not a lot of product, but it is a way to make decent production molds.