Nadair UNPL201-3K-3WH Wired LED Puck Lights (x3) Plug-In Lighting, Can Be Surface Mount or Flush Mount, Easy To Install, Daisy Chain, 3-pack 3000K Warm White

The media could not be loaded. This is the best remote wired puck light around! I bought a different brand earlier, but that remote never worked consistently. This one worked perfectly and easy to install. I chose flush mode on ceiling, and ran the wires through the ceiling into the attic that is over garage, then plugged it into outlet that garage door opener uses (no wires showing by the lights which I love)

My 16 year old halogen under cabinet lights were falling apart due to age/heat. I knew it was time to change when the covers started to crumble.I ordered a set of these as it appeared the plugs were the same as my old lights.I was pleased to find that the mounting and the plugs were the same, so I left in place the wires and just replaced the lights.Difficult mostly to work upside down, needing mirror and flashlight ... but very pleased with the results.These overall are much brighter at the top end (dimmer), but provide a clean light that was very close to the old xeon\halogen lights we had.The temperature is the best part. No more worries about the heat, or putting any appliances under the cabinet and too close to these.

Easy to install to my existing wiring. A little snipping and solder and I had 2 sets installed in about a 1.5 hours. The l8ght out put is a great warm light with plenty of lumens.

I needed to replace a set of about 12 xenon puck lights with bulbs that burned hot and burned out periodically with LED lights. I was wired for 120 volts with a capacitive 3-way dimmer switch. These lights, like many or most LED lights, do not dim with lowered voltage. No matter. I replaced the 3-level dimmer with an on-off switch. They look great, work as expected but were fairly difficult to install.They chain together with male and female plugs putting them about 9.5 inches apart. So the first problem is locating screw holes at the appropriate distance for two lights to connect after they are screwed under the cabinet. The second problem is that the arrangement under the cabinets does not quite lend itself to precisely equal spacing. OK, so I will have to cut wires and splice them to new lengths with soldered joints and heat-shrink tubing.But the main reason these are difficult to install is that you have to work upside down using either touch or a mirror with a flashlight. I laid out pilot holes with a cardboard template, drilled small holes with a small drill and then had to attach the plastic frames using a very small philips head screwdriver working with mirror, flashlight, magnetic screwdriver, Once I had all the plastic frames screwed under the cabinets, I inserted the light bodies (kind of fiddly to get them oriented and twisted in) and connected all the ones that connected directly. Next step was to hook up all the jumper wires that spanned cabinets which I soldered and closed up with heatshrink tubing. Finally connected all to the new capacitive switch and bingo: Fiat lux! I finished the job with a glue-gun to tack any drooping wires to the undersides of the cabinets.Very happy with the results. But installation was not easy. One final note. The manufacturer could save everybody some time and trouble by eliminating the little silver labels that have to be peeled off each light and cut off each wire (at the slight risk of cutting into the wire itself). I didn't look to see what they say. Probably that there is electricity involved which can be dangerous..

Installation was easy as I used double stick tape. They've been up for several months now and holding fast. Quite bright and a pleasant warm color.

I installed these about 16 months ago. In that time, I've had a couple of different ones that were acting intermittent. One would stop working for a couple of days then come back on, then a couple of weeks later another one would do the same thing. They've all been working recently but then this morning I heard a pop, and one of them had blown and smoked up the kitchen for a while. There's nothing like that burnt electrical smell to really tie the room together.

Had hard wired lights under the counters that were shot. Spliced these babies in and they look good

It is good as what the price you pay. So far the quality is ok. But What I can suggest . This product is only good for flush mount. Because the product looks some kind of flimsy.

We bought it to mount underneath a small hall table that we have, to illuminate nice things that we put on the little shelf below. The purchase was prompted when the bulb in the halogen puck light that I had mounted years before burnt out, and I could not find a 'peanut' bulb small enough to fit. This Nadair light is well-priced, arrived very quickly, and was simple and easy to mount...I was lucky enough to be able to use screws, and screw holes that had been used for the previous light. Beyond that, what to say? It works.Only complaint is, if it is a complaint, is that it is somewhat brighter, perhaps a bit too bright for the application, and I think it would be too bright for many applications, say, soft lighting in a bookcase or shelf unit. I may, in fact, look for some kluge, perhaps hang some sheer fabric or a soft photographic filter of some sort under it, at some point in the future.But the essence is, it works and the price was right, it runs pretty cool and it's efficient in terms of energy use.

Easy to install, nice and bright, work well. Seem a bit cheaply made but overall 4 star

Ordered 2 packs and thought I was getting 2 packs with 3 lights in each pack, but instead received 2 one packs. I tried to order again tonight so we'll see how this order turns out. It is deceiving because there is no product description telling how many lights are in a pack. I just went by product pictures and the last picture showed a 3 pack. The lights are reasonably priced and give good light . They're going under my cabinets. Would give a 5 star but can't because of confusion.

Those replaces old IKEA recessed cabinet puck lights that used halogen or xenon lightbulbs. I had a very hard time finding new ones using that kind of bulbs that would be the same size. So I decided to try these LED puck lights which fit perfectly in the pre-drilled holes of my kitchen cabinet.I included pictures for on and off look. They are very easy to install, and honestly, the price is very reasonable. Hopefully they’ll last for a long time.However, the description is misleading: the casing is plastic, not aluminum. Still, they work great and it took me only 2 minutes to put them in place. Moreover, it says that they are dimmable, sort of implying that the switch is a dimmer. It’s not, it’s a simple rotating on/off switch. Perhaps they can be dimmed, but certainly not at the source.When used as recessed lighting (the other option is « surface mounting »), be aware that the instruction manual advises NOT TO INSTALL them in fully enclosed cabinets for safety reasons.

My cabinet required a 3 inch light. Made this one work but not too happy with it.