WALI Speaker Wall Mount, Surround Sound Speaker Stand with Adjustable Swivel Tilt Angle, Small Bookshelf Speaker Mount for Living Room, Home Theater, Hold up to 7.7 Lbs, (SWM202), 2 Pack, Black

These WALI speaker wall mounts work exactly as expected. They’re sturdy, well made, and easily support my speakers without any sagging or movement. Installation was straightforward, and all the necessary hardware was included. I really like the adjustable swivel and tilt, which made it easy to aim the speakers precisely where I wanted them for the best sound. Once positioned, everything locks in place securely and stays put. They look clean and unobtrusive on the wall, and the build quality inspires confidence. If you’re setting up a home theater or surround sound system and want dependable wall mounts, these are a great option. Very happy with the purchase.

I have Edifier R1280DB speakers and I wanted to position them to the ear level and did not want them to occupy the desk space anymore and not settling down to using stands of any sort. They are nicely packed and come with all the screws necessary to mount it and secure the speakers. I was concerned that due to the powered speaker weight, I will need to screw the speakers in however, the clamping design is so intuitive and strong that I am sure itll hold and I save my speakers from drilling into which is a huge plus. Another concern was rattling of any sort or distortion which also has not proven to be the case perhaps thanks to the soft fabric material that is glued everywhere where the clamps meet the speaker, I must admit this was cleverly designed and I approve this 100%! The only issue I had was that I mounted the speaker in the clamp before seating the clamp into the wall mount part, I did it nice and centered also been careful not to push off the rubber pads only to find out I have to take the clamp part off because I forgot to put in a mounting bolt with a plastic washer first. After doing that correctly another issue was placing it this way onto the wall mount part, aligning the bolt through the plastic arm and then wall mount metal while maneuvering the heavy speaker with attached clamp part... I could just do the difficult work first and then mount the speaker on assembled wall mounted clamp but I did want to have it perfectly centered and not to damage the rubber pads of the speakers and this could be done only with the speaker being up side down. As I was almost done, I could not understand why I couldnt finish off the very last step which was same steps as stated above but on the left speaker, upon screwing a bolt with included nut, I placed a washer from underneath where Clamp part meets the wall mount part, routed the bolt through, placed the nut (part: N8 Nut-h) and started to twist it counter clock wise, luckily I didnt let go of the speaker right away, I wanted to make sure theres grip and resistance as I kept screwing it in, to which I realized Im twisting this nut for good half minute, I reversed the turning direction and same thing, no resistance, it just loosely kept turning. So I took the speaker off and then inspected the inside of the nut. BIG DISAPPOINTMENT and anger overwhelmed me. The nut has no thread! How am I supposed to finish my project? Luckily I do keep all the screws, bolts, washers and nuts from old furniture and I did happen to have a metric M8 nut in the house. Otherwise I would have to run to home depot and waste at least 40 minutes of my day which I find very sad! Sad is the look of it now as well. The nut I'm using is screaming compared to the right speaker which I hope is a temporary solution as I will be contacting the seller regarding the nut issue and post the results here in an Update form. Otherwise a 5 star item, well, I would give it 4 because I wish it could be retractable and erectable when it comes to distance from the wall but then I assume my wanted feature would cause rattling and imbalance in the entire assembly so 5 star it is for the product as it is sturdy and holds a powered speaker under any tilted angle desired and rambling bass it wont give in, hold speaker securely and without any damage to it whatsoever, so if youre using it for passive bookshelves w/o rubber pads on them, even better - simple install, just make sure youre securing this to a wall! Physics are at huge play here considering these have to hold across the bass factor which would loosen up any screw from a drywall without serious anchoring. Edit: Contacting the seller was a breeze and received replacement within just a few days by mail free of charge. I offered sending the defective part back which was not necessary and seller sent me two nuts actually. Very friendly and professional service. Definitely great company standing behind their products. Regarding the items functionality, nothing has changed since day one, hold speakers in angle you tilt them at, while moving them left, right. The sound clarity I am getting now is unbelievable and virtually makes me feel the sound comes even from behind me. The way I have them tilted downwards 5 degrees facing my ears the way I can see left speaker's right wall with my right eye opened but when I close right eye, left eye cant see that side wall only face of the speaker. Same applies in reverse order to the right speaker. The setup is 60 degree triangle in about 1 yard distance. Would NOT be achievable without this product. Reviews do not lie. If youre considering between other products of same price range like I did, these tilt and have foam padding, they dont rattle and are very very sturdy. 100% Recommended!

I am very pleased with this pair of brackets: - The metal parts of the brackets are very sturdy and good quality. The only parts that are little flimsy but are of no importance to holding the speakers are the plastic pieces that cover the wall plates - The metal pieces have a very nice black powder coat paint. - The wall mounting hardware (screws, etc.) are sturdy and of good quality. - The instructions are clear and good, and the print is not so small that you can barely read it. - Once assembled, they turn and swivel nicely, but also stay put once you position your speakers. I am using mine with Celestion F1's that are my rear channel speakers. Now for the thing to consider: Your speaker cables. If yours have banana plugs or any other higher grade terminations that are wider and/or longer, you may find you are NOT able to feed them through the cable management channels and cutouts you would use to hide your cables inside the mounting brackets. For example, I have Mediabridge 16AWG ULTRA Series cables running (under my floor and up through my walls to hide them even further) to my Celestion F1's that are my rear channel speakers. These Mediabridge speaker cables are pre-terminated with banana plugs and are good (16awg), but by no means are the best and thickest cables available, and they would NOT fit through these WALI brackets as-is. I liked the brackets well enough, though, that I decided to widen the access holes with a Dremel Motor Tool and a diamond cutting wheel. Because the access holes are on top of the brackets, the less than perfect cutting I did is not visible. Not everyone, though, may have the means and comfort level for this kind of DIY modification. This is the only reason I give them 4 stars instead of 5, but for $25.00 for the pair of brackets I think they are a very good value. Craíg

I received these yesterday and installed them within the half-hour (including grabbing my tools)! The previous owner of my house had dinky satellite speakers up that I had been wanting to replace for a while, and after some research I decided to give these mounts a try for my bookshelf speakers to use as surround speakers. My speakers measure ~7" wide and a bit more than 10lbs each, and the mounts hold them perfectly secure (I have them pitched slightly downward). These mounts have foam lining the base, where the speaker makes contact, and the mounting brackets, so no metal comes into contact with your speaker finish. Since I angled them down slightly, I went ahead and cut out a small square of non-skid to sit the speaker on for added security. I don't think the speaker would move either way, but I'm risk averse, so I tend to err on the side of caution. *PLEASE NOTE* The anchors that come with the mounts are concrete anchors! If you want to mount on drywall, you will need to use good drywall anchors or toggle bolts (I'd recommend toggles, personally). I was able to find a stud for one side, however I used toggle bolts for the other mount. The mounts have concealed cable management - the speaker cable enters through the rear of the mount and comes out through a hole on top of the mount right behind the speaker; it's easy to use and looks very nice. I wound up not using the cable management since my wires were preexisting and didn't have enough slack. I've only had them up for a day, but they went up easy and the speakers aren't going anywhere! They look nice and do their job well! I'm including a few photos, one of which shows the cover slid forward to reveal the actual mount (some people have been asking about how it actually mounts to the wall).

I think these mounts are great! Easy to install and hold these speakers which are 10 pounds each, The only thing I would like to recommend is making a rubber rectangle for the front plates which would stop them from moving so easily. Overall very durable and stable.

Great mounts! Hung up some pretty heavy Vintage Polk Audio speakers in the garage. Worked awesome! Easy to install and a great value!

These WALI bookshelf speaker wall mounts were purchased for a large set of Klipsch RB-61 reference bookshelf speakers. These speakers are 12.3" (D) x 8.5" (W) x 15.4" (H) and weigh about 35 lbs. per pair (~18 lbs. each speaker). Selecting a wall mount that could support their size and weight was a concern. I didn't want to get something that would bend or pull out of the wall. I also didn't want to install support screws into the side of the speaker to ensure it stays on the wall mount. These are brand new speakers, and I wanted to keep them that way. After careful research of all mounting brackets on Amazon, I decided to purchase the WALI brand mostly due to the positive reviews. I'm very happy I did! The mounts came yesterday, and I immediately installed them. As others have commented, they do need to be installed in wall studs. Hardware is supplied for mounts into wood and brick. They do not accommodate mounting into metal studs or concrete block. You probably can, but you'll have to provide your own mounting solution. Mounting the speakers was straight forward. Use a stud finder to locate the stud, place the mounting plate on the wall location and mark the holes, drill small pilot holes, then screw the plates into the studs. The plate has two screw holes for the provided wood screws. One is high enough to use an electric screwdriver/drill to install the screw. The other screw is very close to the support arm. My drill was too large to drive the screw next to the support arm. That screw had to be manually hand screwed. For this reason, a pilot hole is necessary for at least the mounting hole by the support arm. One thing I was very pleased to see was the way the speaker is held on the mounting bracket. An adjustable screw is provided on each speaker clamp, one on either side of where the speaker will sit. Tightening or loosening these screws moves the clamps in and out. So these clamps use pressure to hold the speaker. After I installed the mounts to the wall (which took about an hour), I placed a speaker on the mount and tightened the clamp to find it held beautifully! Even with 35 lb. speakers, the clamp was tight enough to hold the speaker with no problem. My speakers are mounted relatively flat, pitched slightly down. Even though the clamp has screw holes where screws could be driven into the sides of the speakers, I found this wasn't necessary with my installation. The screws for this, by the way, are provided with the speaker mounts. If you need to install them with the added screw support, you don't have to purchase the screws. I'm very pleased with this product. The supports are made with good quality, thick metal, all the hardware is provided, documentation was adequate, and our speakers are held firmly in place. Best of all, the price is excellent. What more could I ask for?

I purchased some medium-sized bookshelf speakers to put in my mancave and knew I needed a sturdy wall mount option for them. After taking some measurements to ensure they would fit, I bought these wall mounts and could not be happier. They arrived quickly, and once I had everything unboxed and took a quick Look at the instructions, I had them mounted in about 30 minutes. Half of that time was really figuring out where I wanted them, so these are super simple. The adjustability is great and once I found the right angle and pitch, everything clamps down nice and tight. The grip pads that hold the speaker in place do a great job of dampening sound vibration as well, as I was worried these might rattle a bit. But they are solid and exactly what I needed. I would definitely buy these again and would recommend them to anyone looking for an easy speaker wall mount solution.

This product worked EXACTLY as I hoped. It held my speakers with ease, is totally adjustable, and really solid & strong once fastened to the wall. The quality of components is very high, featuring a heavy & strong metal assembly. Not much more to say, these speaker wall mounts are likely one of the best options at the price point!

Excelente calidad, acabados, materiales.

Fast processing and shipping arrangement from the store. The mounting bracket looks sturdy and good quality. Came with an installation kit. Yet to install.

Great

غير متوافق مع سوني بحكم عدم وجود مكان للتثبيت في السماعة. استخدنة لازق دبل فيس لتثبيت السماعات