– Invisible Ring Size Adjuster - Ring Reducer for Loose Rings | Ring Tightener & Spacer | Ring Sizers, Grips & Guards for Loose Rings Ring Adjuster Adhesive

Really simple to use and does a good job. My men’s wedding ring gets a little loose in the winter months and this product has worked brilliantly. It’s hidden from view and comfortable unlike the products that wrap around the ring. Not sure how well it removes yet as this is my first time using it. Brilliant product so far.

Due to arthritis, I had to cut off my wedding ring. I had it professionally made larger however it could be a bit on the loose size (better than too tight). I used this over approximately a quarter of the internal diameter. Added just enough to give a reasonably snug fit while still being able to take the ring off. Very impressed, easy to apply and set using the UV lamp. If you add too much, just trim with a sharp knife. It also stays in place, even in the shower or when doing the washing up. Have had this on for 4 months and no signs of it coming off! Just build it up in thin layers until the desired size is achieved.

The gel does make the ring smaller and tighter. However because of my knuckle, it is still a bit loose but a lot better than it was. It is easy to apply to the ring and drys quickly under the supplied light.

Excellent

The bottle of glue had leaked and everything is sticky. Haven't tried it yet, but will comment more once I've cleaned everything!

I was dubious purchasing this as I had tried most ring sizer's. All of which ended up in the bottom of a draw or in the bin! My diamond engagement ring and diamond wedding ring would spin round in opposite directions, due to weight loss they had become too big. This product was easy to use and worked a treat I used it with both rings together almost making them as one and they do not budge. I'm so please with the result which is invisible and comfortable also knowing I don't have to get them both resized. well chuffed I bought this product

Im not happy about this product at all. At the beginning it was doing amazing job. I was very careful to not make it wet. It was fitting well. But after roughly 10 days it just came off. Im not happy to apply it every 10 days. I rather spend my money on some other ring adjuster.

I've been losing weight and I'm on HRT, so my cherished ring has been sliding off my finger. I moved it to my middle finger, but it just didn't feel right, and I didn't want to get it adjusted because I know my arthritis will cause my knuckles to swell. Enter this. Everything came as advertised, and although the ring holder was a bit awkward, it also had some clay putty that held the ring perfectly. The resin was gloopy and easy to apply, and cured near-instantly under the provided UV lamp. There was some overspill, but it was more that the resin relaxed than it ran out. A small pair of sharp nail scissors removed the majority of the excess and a simple nail file brought the resin in line with the rest of the ring - it's invisible while on my finger and doesn't spoil the look at all. Additionally, while cured the resin has a gentle curve to it and is soft enough that I don't feel it constantly bumping against my finger. I presume that I'll stop noticing its even there after a few days. Everything came about as advertised and it was definitely worth the money, especially since there's more than enough to redo the ring if required or do others. Fantastic.

Comodo, semplice da usare, invisibile. Ci vuole almeno un po di manualità e precisione, gli strati devono essere sottili ed applicati in sequenza facendoli catalizzare uno per uno. La lampada UV per la catalisi, (indurimento) non ha batteria e deve essere collegata all'alimentatore per funzionare. probabilmente per motivi economici non viene piu fornita una pinza porta anello ma una specie di plastilina da modellare appositamente, funziona ma ... cheap... In caso di colature, é semplicissimo con una lametta di un cutter, rifilare gli eccessi, quello che rimane dopo l'aggiustamento, incredibilmente é lucido e trasparente, e non opaco graffiato come ci si aspetterebbe. Ho applicato diversi strati consecutivi seguendo le istruzioni ed ho ottenuto una riduzione di misura importante, del tutto invisibile quando indossato. lo consiglio molto. Nb Gli UV della lampada induriscono il liquido ...quindi la boccettina è da tappare ed allontanare prima di accendere, altrimenti ci mette un momento ad indurire il contenuto del beccuccio se appena appena prende un po di raggi UV !!!

Update: I’ve been using this since August 2025. It is now February 2026 and I can report without a doubt that this is an awesome product. Just tonight I reapplied some UV resin to compensate for the erosion of the UV after constant wear. It was by no means worn off, but the ring had gotten slightly looser. I also used it to solder together a three ring stacked set. Please see the included photos. I can unequivocably say this product works, and if you have issues with it, practice makes perfect. Just make sure you cure it for an extent period of time. It should not be sticky. I used a wooden clothing pin to hold my rings under the UV light and it worked perfectly. So just like the title says, all this is is UV resin. You put thin layers on the bottom of your ring to create a spacer that keeps your ring from spinning and gives you a better fit. As is usually the case with any product that requires a bit of finesse, practice makes perfect. If you’ve never used UV resin before, or your hands are shaky, you can expect to take several tries before you get this just the way you want it. A word of caution, the thinner your ring band is the harder it will be to apply. This product works by using surface tension to keep the resin firmly on the band. The less surface, the less tension. The resin is going to have a greater chance of dripping over the sides. Do not be dismayed though. Just get yourself a sewing needle, sewing needle, etc., and use it to scoop up the viscous UV resin and re-deposit it on the band. Having some resin on the sides is actually a good thing because there’s more surface coverage, which means you’re going to have better adhesion. How long this UV resin spacer lasts hinges completely on what you do while you wear your ring. If you’re constantly dunking your hands in hot water, or your ring is constantly banging on a hard surface, like a desk or a keyboard, chances are your spacer is going to detach a lot sooner. Since this is meant to be a temporary solution, all you need to do is pry off the old spacer and apply a new one. Having worked with UV resin for many years I’m surprised I needed this product to remind me of just how versatile and useful it could be. I am pleased that I bought it however, because the light is just the right size. Should you run out of your resin it’s very easy to buy more online, including through Amazon, and it’s not expensive. I recommend keeping the bottle because the application nozzle definitely makes the job a lot easier. Here are some tips to get the best results. What it’s got multiple balls in here how are you doing? 1) Prop your light up in the box, using the bottom leg as a stand and the back of the box as support. The upper leg becomes the arm you then dangle your ring from. 2) use a rubber band, string, or some kind of attachment to hang the ring from the “arm” of the light. Make sure that you can change the position of the ring so that you can cure it from both sides. 3) use a small mirror, or a piece of cardboard wrapped in the shiny side of aluminum foil and place that in front of the lamp while curing. This will reflect the UV light back towards the ring and give you a better cure. 4) make sure that your ring has been wiped down with alcohol. This will ensure that there are no oils or dirt present that could prevent the resin from adhering to the metal. I would not recommend using this on plastic as you could form a permanent bond. 5) don’t be afraid to do multiple layers and build up your spacer. You don’t have to do it all in one go. Just make sure that you completely cure each layer before you go onto the next. Use a needle or toothpick, or something similar, to manipulate the resin. This will give you better control and better results. Use a little bit of sandpaper, preferably wet dry 320 grit, and just lightly go over the UV resin to give it some tooth and help the next layer stick. It’s not a requirement, but again, we’re looking for best results. 6) if you’re having trouble with your UV curing, try this. Start with a clean ring. Put a small amount on the ring and flash cure it, meaning you’re going to have it under there for no more than 30 seconds or so, just enough to harden the outer layer. This will prevent the resin from moving when you take it off the lamp. Then submerge the resin covered portion of the ring in water and cure it the rest of the way with the lamp. This often speeds up curing and helps eliminate the stickiness that can come with some resins. Upon completion of curing, you can go over the resin with some alcohol to clean it up. 7) if you have an uncomfortable amount of spill over, resin is just hard plastic and can be sanded away. Use that same 320 grit sandpaper and gently sand away the unwanted portions of resin. You could even use a Mani Pedi kit if it comes with one of those electric files. Very helpful! Emery boards are another very helpful tool. All in all, I really really like this kit and I feel very stupid for having waited almost 4 months to use it. Now my brand new wedding ring fits like a dream and I don’t have any more issues with it spinning and ending up diamonds down. I highly recommend giving it a try and with just a little bit of practice, you’ll find that it’s easy to use and gives you that comfortable fit you’ve been looking for!

J’avais un souci insolvable avec mes bagues qui est maintenant résolu avec ce réducteur En effet mes doigts gonflent selon les saisons et au fil de la journée : une taille est parfaite le matin mais trop juste en fin de journée et la nuit ce qui me procurait de l’inconfort et m’empêchait de porter celle que je voulais 😓 Ce produit est juste parfait car il permet d’ajuster la taille en posant le produit sur le bas de la bague (ce qui l’empêche de tourner) néanmoins les espaces laissés libres (ou la résine n’est pas posé) procure un espace suffisant au doigt pour gonfler Le produit est relativement facile d’utilisation ( veiller toutefois à garder l’anneau droit pour ne pas que la résine non polymérisée coule) et est extrêmement résistant dans l’usage (adhère parfaitement au support) Le retrait est facile en l’immergeant une dizaine de minutes dans de l’eau bouillante Testé sur bague en argent rhodié et or Les plus : Permet de réduire de 2 tailles max les circonférences Facile et rapide à poser Extrêmement confortable et discret (j’ai essayé plusieurs solutions et celle ci est de loin la meilleure) Permet d’ajuster la taille quand la réduction chez une bijoutier est techniquement impossible Les moins : Application très compliquée sur les petits anneaux (-de 3mm de largeur) ou la résine tient difficilement sur le support et coule sur les extrémités Non adaptée pour les réductions supérieures à 3 tailles Notice en anglais néanmoins les dessins peuvent remplacer les consignes car pose intuitive et facile Je recommande vivement

I didn't want to permanently resize my rings and didn't like the look/feel of having a rubber around the rings. This glue is perfect. It's slightly tricky to cure it specially if the band is thin but the key is to start slow and build it up layer by layer. The little curing light is also very cute and sufficient for the purpose.

Buenísimo llego rápido y en unos minutos lo apliqué seco rápido con la luz ultravioleta y me encaja perfecto en el dedo, volvería comprarlo