Topfit for Tesla 2022 2023 Model Y Model 3 Performance Pedal Pads Cover Foot Aluminum Non-Slip Pedals Accessories

Great upgrade to make the pedals look nicer, much better than the stock pedals. Install was a slight tougher than I expected by as one reviewer suggested, I left them out in the sun for a few hours which helped soften up the rubber. They both went on pretty easily and I just needed a trim tool to finish the job off.I must say they add an awesome touch to my otherwise all-black car. Looks just like the performance model and feels great while driving. Highly recommend getting these.

Remove rubber break cover first. Note: no cover to remove for the accelerator pedal.Installation took some doing. Used a heat gun to heat the rubber to make it a little more softer and pliable for installation. Be careful to not over heat. In addition, I rubbed a few drop of liquid dish soap around the rubber perimeter of both pedals to help reduce friction when sliding and positioning.Work from the upper right corner for both break and accelerator pedal. Use fingers to work around the perimeter to pry the rubber over the pedals.Using a thin work glove can help save your fore finger from getting pinched / cut as you work the rubber around the pedals.Once installed the pedals are solid.

This is actually the first modification I did on my car. It looks great and for the price it gives you a very nice design on your car for some it might be difficult to install because of the fitment on the pedals however, since I installed it on my vehicle, it has not moved at all and this was approximately 10 months ago. They are very easy to clean.

This was such a difficult install. I would say “how bad do you want these”? If you want them more than you want the pain that comes with putting these on. Crushed fingers, destroying your hands and ackwardly twisting your body into unnatural positions to finesse these on. BUT they are great and you will feel victimized and victorious at completing

Like the looks, dislike the accelerator pedal installation

Just as the product promises, went on super easy, and look great. They have been on for a month now and look just like the performance model pedals. Stop looking and just buy these for your model 3

They jazz up your model y Relatively easy to install and look good.

This is a great looking product, and I'm happy I installed it! I didn't believe, though, that I would mangle my fingers in the process like so many others on Amazon and even YouTube have explained! Fail! LOLFirst -- these are a nice quality, but they do stink with a prominent rubber scent at first. I let mine air out for a day before I attempted install.Next -- the accelerator pedal was really not too difficult to install for me (for some it's the opposite). I didn't try to warm up the rubber prior to installation, and it really only took a minute. I started with the far side and the bottom, and "unfolded" the left side without too much trouble.Next next -- the brake pedal install was rough! Definitely seek out a YouTube video for the install process, but it boils down to the surrounding rubber fitting being very difficult to get to encircle the brake pedal. Two of the four sides isn't too difficult. The third side requires a lot of prying. The fourth side, well, it's nearly impossible because of its very tight tolerance. I enlisted the help of a spudger unsuccessfully and finally got the last side "unfolded" by using a small flathead screwdriver. My fingers DID get mangled in the process! (see pic! Somehow tore my index finger, bent my middle finger nail, and scabbed up my ring finger! lol)Really, these are a nice touch, just be persistent when installing and watch those digits!

It was a painful experience installing it. I gave up after spending 20 minutes on my first attempt. Took less than 3 minutes to install both after watching Youtube videos.For those struggling:1) Put them in a ziploc and soak them in hot water for about a minute. It should loosen up the rubber flex.2) Detach the OEM brake pedal cover3) Start from the top (tuck in left top and right top corners), bottom lip, then rest corners by prying the rubber4) For the accelerator pedal, you don't need to detach anything. Start from the right side (tuck in right top and right bottom corners), left lip, then rest corners by prying the rubberI know most people struggle with the accelerator pedal, but for me it was much easier somehow. You really need to put a lot of force with your fingers though. I didn't use any tools.

Followed the installation instructions carefully (soak in very hot water to soften the rubber, then carefully install). The accelerator pedal was fine - a tight fit as expected, but with a bit of work successfully installed it. As soon as I looked at the brake pedal cover, it seemed obvious the rubber was too small to wrap around the brake pedal. Sure enough, tried multiple times to stretch it over the brake pedal, there was just no way to get it onto my Model 3’s brake pedal. In the end, the aluminum detached from the rubber, and the cover was ruined. Looking on Amazon at other similar products afterwards, I finally figured out that the original rubber pad on the brake pedal has to be removed before installing a pad like this one (but too late, as my aluminum pad was already ruined). Giving it a one star, because (a) the instructions made no mention of this key point and (b) poor construction, it came apart in my hands as I was trying to stretch in place, leading me to believe it would have fallen apart on it’s own after some regular use.

Took ~15 minutes and a fair bit of elbow grease to install on my Model 3 but they look good, are made of real metal unlike some other ones on Amazon, and fit tight. The accelerator pedal was harder to install.Side note. It's pretty hard to find on Amazon by searching for some reason but I got the Topfit one for the Model 3/Y, not the model S/X which has a bigger break pedal. If you're looking for the M3 one you might have to flip through a few pages.Hopefully they hold up. Will update if they don't.

These pedals not only look nice but are functional as well, especially with the accelerator pedal. I find that the accelerator pedal in the base Model 3 is a little too small and the provided cover is quite a bit wider and more substantial.

Bought for my 2021 MY. Took about 15 mins to install after soaking in warm water for 15 mins.Looks good with a snug fit. Have only had it on for a few days so can't comment on durability.So far so good!