OLSON SAW SF63510 Coping Saw Frame Deluxe Coping Frame/End Screw, Original

Fantastic coping saw for the money with a great blade sharper than most stock coping saw blades.Pros• No tools needed to tighten or loosen: the thumb screw on the end lets me tighten and loosen completely without needing to reach for a wrench or screwdriver, where as a lot of cheaper coping saws need to be tightened firmly with a tool to stay tight and/or don't have a large enough screw to grab with your fingers. Even if you do end up using a tool, you can still easily get it 90% of the way there with your fingers.• Handle and thumb screw tighten/loosen quickly and hold tight enough without having to make it "super tight"• Handle is comfortable and easy to work with (though some people find it small)• Changing blade is less of a pain than other saws as the screws are long enough to easily swap the blade when loosened - you won't have any trouble with screws/pins falling out because you have to unscrew the end all the way for an untensioned blade to reach (looking at you Irwin "ProTouch"/"Premium Pro")• Blade easily rotates the full 360 degrees, unlike SOME coping saws (*cough* Robert Larson *cough*)• Good stock blade at a course yet comfortable 15tpi. I felt like it did better than my leftover irwin blades (17tpi) or my generic harbor freight blades(15tpi)• Overall clean and simple appearence with a nice smooth wood handleCons• People with large hands may find the handle to be too small• Tension can be a little bit low when fully tightened, but if this is an issue you can (carefully) stretch the frame very slightly - this adds more than enough.• Some people have said this saw doesn't work well for hardwoods, though I would think that depends mostly on the blade and the user, I haven't used it on anything harder than soft maple.

Overall, great saw. Straight grained handle, very stout frame, plenty of tension. The only thing thing I would do different is replace the knurled round nut with a wing nut and washer instead. It's very hard to loosen the round nut when tightened all the way (I work with my hands all day, this is not a strength issue). 5 stars for value. 4 stars for design. Great saw for the money. Can't beat it.

I bought this saw specifically to cope crown and base moulding for our living room. I decided to cope my corner ends instead of mitering them because I know not all corners are 90º and my walls are the old lathe and plaster making them uneven, unlike walls finished with sheetrock.The saw is sturdy and reversing the blade is easily done by adjusting the thumb screw and handle. I found it easier to use holding it with two hands on each end keeping a grip on the tension "levers" so the blade doesn't twist and bind. I found the blade has a tendency to twist if I just held the saw by the handle. The two hand method gave me better control on cuts, especially cutting curves in the moulding.The pictures were taken after using it for the first time. I will even out the bottom portion of moulding and prime it before it attach it. This small piece butts up next to a door casing and corner wall.Picture #3 is what it looks like dry fitted.

It's not that the Olsen coping saw is the best one made, but it is very good at its job for a very reasonable price. For even money I would buy the Knew Concepts coping saw any day; however, at 15 times the price, I'm going to wait until I find that I need to pay that much to get the job done well. So far, the Olsen saw does what I need. In fact, I bought two of them so I could have them set up for different tasks, and I'm still only out about $20. The first Knew Concepts saw I buy with be the fret saw, because it is so far superior to any other fret saw on the market and is about 2/3 the cost of its coping saw sibling.My Olsen coping saws arrived in good condition and were immediately put to work with good effect. I also purchased some Pegas skip tooth saw blades that are very highly regarded, but I haven't used those enough to review them yet. Chris Schwartz's (well-known woodworking author/guru) praises are good enough for me and are much more reliable than my opinions.

This saw frame is easy to use and has a deep enough throat for most projects. Make sure to pay attention when ordering replacement blades. The ones recommended are extra fine.

Used it for cutting very small non dense pieces of wood (think balsa wood) they worked well but you couldn't use them for anything other than very light duty work.

Good Quality / Value $15Coping came with 1 Starter Blade5”-6” Pin Scroll Saw BladesWood handle nice..👍🏼 compared to plastic..

My base boards matched perfectly using this.