[Healingshield] Premium Acoustic Guitar Pickguard Basic Type Clear matt

There seems to as many pickguard possibilities out there as there are picks. They come in many types of materials, colors, designs, curiosities, and potential solutions. With that said, I simply could not make a decision. So, instead of having to match pickguard color to my guitars, I chose to purchase these clear types. The package comes with 2 guards slightly different in design but using the same basic overall coverage. Laying down a clear plastic pickguard requires 3 major objectives. The surface must be clean and oil-free, you should lay the guard in place to see your final location before removing the protection layers, and finally, remove any bubbles after application. This product comes with the 2 guards, a moistened cleaning towel, a dry dust removal towel, and a squeegee to remove air bubbles after placement. The directions are pretty basic but if you ever have applied a very thin layer of material to any surface, you know the rules. Try to find a dust-free area to do the work. Be sure to use the moistened towel to clean the surface and then wipe the surface with the dry dust-free towel. The adhesive side protection sticker is labeled 1. Remove that sticker and roll the guard onto the surface where you plan the pickguard to be. Using the squeegee, move it outwards from the middle to the edges across the entire guard. Then remove the protection layer numbered 2. Again, squeegee from the middle outwards to the edges until you don't see any major air bubbles under the guard. Very small air bubbles will eventually disappear. If you see some dust or dirt under the guard, that will require you to re-apply the guard. I was able to do both my guitars without needing a re-apply. For the money, this kit is well worth your consideration. Please note that after application, the only way you can tell you have a pickguard is by seeing the edges. The guards are 100% transparent.

A little pricy for what it is and some directions in English would have been appreciated, but overall, I'm pleased. I don't write many reviews, but this one deserves a thumbs-up. It would get 5 stars if it was priced a little better.

I applied this guard to my Ibanez nylon stringed acoustic guitar. The smooth glossy finish of the guitar provided a very smooth and neat application of the pick guard. It took a little effort to remove the air bubbles but the finished product looks great or should I say it is invisible and does the job. Great find and buy. If you have a lot of grain revealed through the finish you may experience a greater degree of air bubbles but I am sure the protection would still be there.

Great concept, terrible instructions, they are written in Chinese? They don't have an online tutorial either I had to find a similar product online and go with their instructions. I have 2 guitars that need pickguard protection and it wouldn't adhere to either. It came with 2 cleaning towelettes, no microfiber cloth and didn't come with 2 pickguards like many other reviews are saying it did, doesn't matter in my case it wouldn't work on either guitar very disappointing.

Exactly what I wanted. I removed the solid black pick guard that came on my guitar and replaced it with this clear gloss one. Removing the factory one was a nightmare. Took forever with blow dryer on low picking and peeling. Then all the sticky RESIDUE left on the guitar! I used a combo of Goo Off, windex, coconut oil, and wet ones and hours of elbows grease to get all the sticky residue off. This applies super easy. Looks great on my black guitar. Highly recommended.

No matter how well I cleaned my guitar & had it dust free the protective pick guard still had dust. Wondering if it contained dust prior to my removing the covers to install.

Nunca había usado uno de estos y lamentablemente no es mate como dice, si no brillo , si es fácil de poner pero no veo calidad en el material , sin embargo por lo menos resolví de momento con el .Vienen dos unidades con diferente corte ,la más pequeña fue la que sirvió en la guitarra Alhambra .

So easy to apply and the kit even gives you what you need if you get bits of lint or dust stuck underneath it out for a nice even seal. I have a blue-green guitar and got the glossy finish, you can only tell it's there if you're paying close attention. Also the kit come with 2 pickguards but only enough to stick/unstick one unless you're doing two different guitars at once. Peels off cleanly using the kit and protects well!

I though the quality of it would be much better. I have the feeling I could have cut a piece of plastic and put it there on my guitar. I find it quite expensive for the price I paid.

Hält nicht

These are amazing pick guards,easy to fit ,and almost invisible,you have to look closely to see it ,I have used these on my other guitars,but they were the patterned type,never given any trouble,also there is no glue involved,no mess if you need to remove.I have fitted one to my Faith Venus high gloss ,and am delighted with the result see photo,I would buy again from this company.

You actually get two pickguards in the pack along with a cleaning wipe, a microfibre cloth and some stickers to remove dust. The instructions are amusing, as if it’s been translated from Chinese via Dutch then into English on a beta version of google translate. Seriously, though, you can make out what it all means. I’m pretty happy with the result, there are a couple of tiny bubbles in there that can be seen in certain light but only just. The pick guard is barely visible on the guitar which was what I wanted and it is unobtrusive. I haven’t tried to remove one yet but I think it’s like a phone protector so I’m hopeful it would come off easily enough and not leave a mark.

This is an excellent product and does exactly what it says in the description... it takes a while to arrive but there were in fact, TWOitems in the packet... different shapes.It does take some care to avoid getting bits underneath when fitting it but no more than when you fit a monitor shield your on camera or iPod.It comes off easily and can be re-fitted and seems not to affect the sound.If you needed to trim it to fit better, cutting at a slight angle AWAY from the edge makes a better job ie; cutting just off the verticalwith the blade leaning towards the shield... I found scissors did not work too well as the edge they left seemed to show against the top.It's a well manufactured product and has all you'd need including squeegee, cleaning cloth etc.