Aerobed 2000012050 King Elevated Double High Airbed Inflatable Mattress, 14-Inch

Bed Leaks over time, no getting around it.Great pump, nice material, really comfortable, and does support weight of two 160 Lb+ adults and our 3 year old well. Fuzzy top is a dust and dirt magnet, if you cover with sheets or foam topper, it doesn't really matter.Here's how to fix the leak issue.1. Check to see that the "Whoosh" Door is closed, it has several click points. This could be the issue.2. If the leak persists, chances are it's at a baffle seam I found each seam edge gets stress over time and small holes / tears occur causing the leak. (See pictures)3. Get some "Seal All" it is perfect for this kind of fix. it's clear, sets fast and woks to seal air leaks.4. Find air leak points, sit on bed after fully inflated and feel each seam edge and you'll feel air escaping.4a. Soak a sponge with water and then go over each point dribble a few drops and look for bubbles.5. Mark each seam point. or... Just to avoid future hassle you may as well just seal each seam edge to avoid future leaks.6. Deflate bed, suck all air out.7. Use a good 1/2 to 1" round glob on the hole or at each seam point.8. Do this in the A.M. and the bed will be cured and ready to sleep on at night.9. After an hour inflate the bed slightly so that the Seal all that goes into the hole doesn't stick internally.10. After 6 plus hours inflate fully, soak a sponge with water and then go over each point and look for bubbles.11. No bubbles? enjoy your reinforced bed.12. Re-apply as needed, some may leak again

First, we like the bed a lot. It's really, really comfortable and the built in pump with a reduction switch is awesome! That pump really works.We carefully followed the instructions about letting it rest and stretch. We did what that other couple who wrote a review did with theirs...we took a few days to fill it. We like ours good and hard under the eggcrate, so we find we top it off every couple of days but that is no big deal at all with the pump - takes seriously 2 seconds. We've slept on it continuously for the last month plus and no complaints at all.If you are used to one of the single layer airbeds, you will notice a slight difference with the double high in that it can feel like it sways (?) ever so slightly once in a while (I am sensitive to movement so you might not even notice - my H doesn't) and very, very slight dip if you are sitting up next to each other...the lighter person will feel a titch higher which we never felt with the single layer king size airbeds.It's a very nice bed and worth the money. When using the single layer ones, we kept having to replace them. This bed has been great.

I really liked this bed. Very comfortable and easy to set up, but after only 5 months it started leaking, when laying on it you need to reinstate it about every hour or else by morning you would be on the floor

So far very good. I took a few days in breaking the bed by leaving it inflated before ever putting any weight on it. Then I had to sleep on the bed for three nights. I thought the bed was pretty comfortable. More comfortable than some beds I've slept on at hotels. Additionally it inflates easily and packs away in a bag that came with it nicely. If I was going to say something negative about the bed I would say it had a strong plastic smell for a few days while I was breaking it in. The smell gradually faded but it would have been unpleasant to take it out of the box and sleep on it right away.

When inflated we like it. However, mattress will not hold air, has a slow leak somewhere. Have to add air in the middle of the night. Submitted to Aerobed for a replacement a week ago and have not heard back from them yet.

Used it for the first time last night, set it up in our toy hauler. Setup was a breeze pump work great stayed inflated all night long. I would definitely recommend this.

Best sleep in a few years... Replaced generic memory foam bed that lasted about 5 years before developing ruts. Fits perfect on the Foam base and fitted sheets, fit!!!

the aerobed arrived and I followed the instructions, by letting the bed warm up to prevent leaks after 4 hours I inflated it and within two hours it became soft and had to inlate again