ERYONE Filament Dryer Box for 3D Printer Filament, Filament Storage Holder Compatible with 1.75mm 2.85mm 3.00mm Filament

This filament dryer is a quality piece of equipment that looks good and works wellIt holds a single standard 1kg spool of filament. You can store the filament in the dryer while the drying process takes place, and during printing you can actually feed the filament directly out of the dryer on either end.You should store your filament in a climate-controlled area with low humidity, but if you have more than a few spools and don't have a dedicated room for them, probably most of your filament is going to be exposed to ambient humidity most of the time. Assuming you don't live in the desert, that humidity is going to creep into the filament, making your prints less than perfect. Filament only lasts for a few years at best under those circumstances, and will eventually print poorly, create bubbles, and get brittle.This dryer can help remedy these issues

So I had always heard how important it is to dry your filament before printing, but I always figured "my house is dry enough I don't need to worry", well I can honestly say now that I've used this dryer that it has made a huge difference! I had never realized how humid it is inside my house until I hooked it up and actually saw on the display, and my filament was just soaking it all up. There was basically no setup involved and after using the dryer for about a week now I've noticed considerably less stringing on my prints. Well worth the value in my opinion!

Has a great form factor and changeable exit feed for the spool. So it's easy to mount to the printer. But feel like it's a little under powered??? I have to run it for a good 5 hours to get the filament to dry noticeably. But may be due to where I live.

Two week update: first roll worked fine. I’ve tried other rolls since and saw zero improvement. I’ve tried rolling the filament within the carrier every hour and that didn’t work. I’ve tried drying for 8 hours and saw no improvement.It’s a shame Eryone has gone downhill. They had great filament and often had incredible sales.This dryer has many quality of life perks to it. In the end, it fails to do its main purpose. I was having trouble with a petg and popped it in the dryer. No results after 4 hours. Dried again for another 4 and still saw no results. I figured that roll was bad and tried a pla that was popping. This didn’t do anything for it. I don’t understand since it gets warm and the built in humidity sensor/thermometer shows a change.Don’t trust the built in gauge. That appararently has no relation to the actual filament. My other driers will have risk of overheating the filament, making it too floppy. This doesn’t seem to get hot enough to work, let alone too hot. I’ll stick with the eibos driers that are top notch. They are a bit fiddly to work with, but actually work as filament driers.I don’t think this gets hot enough. The auto off was also not working which is a big red flag.Original review:This is my 3rd filament dryer. I have two other brands and have my own complaints about them.This eryone filament dryer is great. The top lid is hinged, making it easy to load and unload rolls and the starter line. My other one has a giant lid you need to feed the line through while holding it.I ended up printing a handle for that design flaw, but it’s still bulky. Another has a side snap on lid that’s inconvenient.This eryone dryer makes it easy to load the roll and insert the filament through the hole. There are multiple spots you can load filament through. All are accessible. I’d recommend putting some ptfe into the rubber grommet. This helps prevent the filament from snagging on the rubber. You can also use this as a reverse Bowden or direct Bowden setup.The best feature is this has auto off. Hit 1 2 or 3 times depending on material. No other settings or dial to use. 1 for pla and 2 for petg is what most people would use.Having an auto off is great so you can use this for longer prints without worry about it running too long. Not having to fiddle with dials or temps is also nice. This is more purpose built than my other dryer without breaking the bank.This is one of the few compact dryers I’ve seen that has a fan. Imo, this is crucial to prevent hot spots and provide even drying. The fan is noticeable but quiet.I started this at 54% humidity when off. It quickly dropped to 15%. The filament wasn’t overly deformed when I removed it. This is a problem with my other dryer.Overall I’m happy with this. It’s great and is easy to use. It just works and that’s all you should care about.

After using the Snail M2 for about two weeks now, I can say that I'm pretty impressed with it. I like that it comes with a built in hygrometer, and that it uses both desiccant AND heat to remove moisture from the filament.It's pretty light and takes up a small space. It's not very loud but it does have a small whirring noise while running. I've tested it next to a Neptune 3 Max and I have no complaints, though I did have to sit the Snail M2 higher to account for the large build volume of my printer.This thing is a must-have if you're printing with any filament that has a high porosity, like nylon or co-polyesters, but it's been working great for revitalizing my old spools of PLA too.

Not much space in my work area, but this fits great. Easy to use, good rollers.

I really.like my snail dryer. Its great for sensitive filaments but also being able to print with some older filaments that ive had sitting around for 2+ years. Also found it to be helpful when it was in the 20s the other night in my non-climate controlled garage. Nice quality and small footprint, only drawback ive seen is it wont fit some wider spools but ive only had that issue with 1 brand.

I like the idea of having a dry box. I use it mostly to dry my filiment before I vacuum pack it for storage.I tried feeding my machine directly from the dry box through the hole that is provided. My machine started to studder trying to pull the filiment out. All n all I would purchase this again.

Bra tork, fick nog en nyare variant än de jag läst recensioner på. Denna är har isolerade sidor också.

Dopo anni ho deciso di comprare un essiccatore per bobine, comprando spesso il filo eryone perché sinceramente costa poco e non ho mai problemi, ho deciso di far 31 e comprare pure il loro essiccatore, come sempre non deludono mai, il sensore di temperatura interna e di umidità è uno di quelli che uso sempre che si trova a prezzi abbordabili e funziona bene, quindi se mai questo dovesse dare problemi sarà pure facile sostituirlo negli anni!, per il resto pensavo di non dover aver mai bisogno di lui perché tengo tutto in una scatola ermetica con tutto il necessario dentro, ma a distanza di anni ho notato che il filo si è lo stesso rovinato, quindi mi metterò lì con calma e lo scalderò tutto e userò questa box quando dovrò stampare filo che non uso da un po’ di tempo, anche perché la taglia non è per le bobine più grosse che ho, ma ci stanno lo stesso e girano lo stesso, infatti quella in foto è tipo formato XL ma ci sta lo stesso, stretta ma ci sta! Quindi si dopo tutta questa pappardella ve lo consiglio vivamente! Non fate come me! Non pensate che tanto il filo non si rovina!! Gli essiccatori servono

Ce sécheur de filament est très bien, très performant mais certaines bobines larges ne rentrent pas dedans car la largeur maximale est de 68 mm. Il faut juste le savoir.Sinon les petites bobines de 500g passent mais si on les laisse au milieu alors elles frottent sur la hauteur donc il faut les positionner sur un des côtés, légèrement en biais et ça passe, par contre on ne pourra pas fermer totalement le sécheur mais cela ne pose aucun problème, voire mieux, ça permet à l'humidité de s'échapper plus rapidement que via la trappe ventrale (là où vous mettrez les sachets de déshumidification) car la chaleur s'élevant, l'humidité sortira plus rapidement.Sinon esthétiquement elle est très bien, ainsi que les 3 possibilités de sortie du filament et les deux tubes PTFE fourni (un long et un court).Le seul défaut que je pourrais lui trouver c'est qu'en mode PLA le timer s'arrête automatiquement au bout de 4h et j'aurais aimé pouvoir sécher certains filaments toute une nuit pour pouvoir les utiliser immédiatement après un cycle de 8h mais dans les faits je n'en ai pas eu besoin car en moins de 2h on passe d'un taux d'humidité de 45% à 10%...

Diseño elegante y cumple su función, no me ha entrado ningún documento ( certificado de autenticidad, instrucciones,..) por lo demás cumple con si función

Ich war bisher immer sehr skeptisch was diese Trockenboxen angeht, vor allem da sie sonst keinen Lüfter haben und somit die Wärme sehr ungleichmäßig verteilt ist.Zudem trocknet alles besser wenn die Luft bewegt wird.Diese Box hier hat einen Lüfter, weshalb ich nun endlich mal so eine Box testen wollte.Dazu kommt, das ich viel TPU drucke, aber auch Nylon(PA) und anderes Material das sehr wasseranziehend ist.Bisher habe ich immer im Backofen mit Umluft getrocknet, nur braucht ein Backofen entsprechend viel Energie.Die Box ist wirklich gut.Die Temperatur auf höchster Stufe reicht aus um TPU oder Nylon zu trocknen.Dabei ist der Lüfter angenehm leise und der Stromverbrauch recht gering.Es passen auch größere Rollen in die Box.Ich nutze u.a. Filament von Fiberlogy, das auf recht ungewöhnlichen dicken Rollen geliefert wird, aber auch diese Rollen passen.Die Rolle wird auf 2 kugelgelagerten Achsen gesetzt, so das man das Material ohne Probleme gleich aus der Box drucken kann.Es wird auch Trockenmittel mitgeliefert, das die Feuchtigkeit, die aus dem Material entweicht, gleich aufnimmt.Das Trockenmittel kann dann später ohne Rolle auch wieder getrocknet werden in der Box.Ich bin wirklich zufrieden mit der Box.Entscheidend finde ich das hier ein Lüfter verbaut ist, das macht einen großen Unterschied.