Never Fails - Its A Complete Undermount Sink Installation and Repair Kit Made in USA

I bought and installed these back in February 2017. 3 years later, the mounts are still holding my sink in place with zero issues to speak of. Back in 2017, my stainless steel undermount sink was sagging because the silicone caulking bead between the edge of the sink and the granite countertop was cracked and water was seeping onto the plywood supporting the sink. I waited entirely too long to replace the caulking and as a result, the plywood rotted.The Cinclips was a very simple install. Push the sink back up in place, mount the clips in the desired location, mark the holes for the Cinclip base mounts, drill the holes, screw the brackets in place, and that's it. You're done. Obviously, the cauking around the sink has to be redone with your silicone based sealing agent of choice.I'm sure other people might encounter difficulties based on their kitchen cabinet setup. I was fortunate that kitchen cabinets are modular with vertical boards located 2" to the outside of my kitchen sink, providing me a perfect location to mount the Cinclip bases. Overall, including recaulking, I remounted and repaired my sagging sink in about 1.5 hours total.So long as I keep my sink sealed and the supporting structure completely dry, I have no doubts that the Cinclips wil last the life of my kitchen and I will not be plagued with the problem of a sagging kitchen sink ever again.

Crash!!!! My sink detached from the countertop (thanks contractor). I found these on amazon and saved my bacon. Easy to install and made the sink-countertop more stable than before. Well worth it and would highly recommend these.

Undermount double bowl kitchen sink installed on granite countertop by contractor began to sag at the middle intersection (front & back) of both bowls about six months ago. Could not install additional mounting clips (per initial installation method) due to tight space and inability to remove countertop from cabinets. These Cinclips were extremely easy to install in the tight spaces where the sink bowls meet each other and meet the cabinet woodwork. 1) Recaulk the sink bowl (with clear silicone) where it was sagging away from the granite. 2) Use a piece of scrap wood to wedge the front of the sink back up to the granite. 3) Put the Cinclip in place (inside the cabinet, wedged against the sink lip. 4) Secure the Cinclip with the provided screws to the cabinet woodwork. 4) Remove the scrap wood wedge & that portion of the sink is now fully supported and the sag has been eliminated. 5) If there is still a bit of sag due to imperfect Cinclip installation, add a wooden wedge between the sink and the Cinclip to put additional upward force on the sink. Use silicone to glue this wedge to the sink base. 6) Repeat anywhere else the sink sags.

Great design. Very easy to install. I would highly recommend these. Installed them when previous installation failed after 8 years... Previously the sink was only held by silicone and and 4 blocks epoxied to the granite on the underside. It was installed by the granite company, no less. I followed instructions from Cinclips video and total jnstall time was about 45 minutes (including prep time to clean up the granite and the sink. Would have rated 5-stars but had to "rig and alter" the small front-side arm to fit my cabinet that has a faux drawer in the front. It would have been so much easier if I could have adjusted the length of the arm. Still a great product. Buy with confidence!!!

These may be one of the easiest, and most cost effective, ways to remount a sink. Let me explain:My kitchen sink recently pulled away from the silicon sealant, and the mounting brackets were improperly mounted and sized for the weight of the sink. The mounting brackets had actually bent about 15-30 degrees each, the right side of the sink on the worse end of that range.I had tried remounting with new brackets but ended up with them bending as well, much to my surprise. To be fair, I frequently fill my sink with about 7 gallons of water and will do a week's worth of dishes in a single sitting. Not the best plan if the sink isn't secure.So when I was told that these cinclips would mount into pressboard and hold my fully filled sink, garbage disposal and associated plumbing, I was skeptical. And it turns out I was wrong.They are shockingly sturdy for what is only 4 plastic mounting brackets (5 when you use the rear/front short bracket) being held into pressboard by 4 screws each.They are almost as easy to mount as the company's tutorial video depicted. Yet another surprise.My only issue was the short bracket that I had to install in the rear of the sink, which was a construction problem unrelated to this product. If you do not have about 4 inches of front cabinet to screw the bracket into, you may be stuck manually attaching the 4 screws on the short bracket while working behind your sink in a space only 3-4 inches wide. That being said, many other users said they didn't even use the short Cinclip.And use gorilla tape to hold up your sink while installing it. I opted for duct tape, and decided after installation to read about the difference between the duct and gorilla. In testing: gorilla tape is stickier, holds more weight, and is more water resistant. All good things for a sink project. In practice, I've still never used gorilla tape so I'm going on recommendation.The cinclips have now been installed for a month. The sink did initially settle about a quarter inch and pull away from the silicone I had used as a sealant. I reapplied the silicone 2 days after installation and have had no peeling away since. I believe this would have been avoided if I had gone with the gorilla tape and not the duct tape.Should I ever need to remount another fallen kitchen sink, I will most likely use the cinclips system again. It's simply too convenient, especially given that it can be used the same day as installation.**Update 10/23/16**My wife and I moved into a new house this year, and while doing the inspection I realized that the kitchen sink was IDENTICAL to the sink in our old home. Looking underneath the sink I saw the 4 brackets were also identically installed. Having spent about a year with my previous cinclips not giving out, I opted to buy and install them before the sink could peeled away. It took me 5 minutes to install the 4 brackets compared to the 2 hours it took for me to remove the old brackets from the sink, clean the caulk/silicone off, remove the overtightened garbage disposal fittings, clean up the resulting water, reapply caulk, tape the sink, and THEN install the cinclips.If you have the option, install these before you have problems. It was so much easier ;-)

These are awesome! I have a heavy, custom stone sink and I wanted to put one more support on the back. Not even sure I needed it but I figured better safe than sorry. When I reached out to the company they shipped me another immediately. This is the one you want, and you can feel good about getting a quality, made in USA product from a quality business.