Electriduct Large Hook Channel Cable Raceway Desk Cord and Wire Organizer - 58 Inch - Black

Large Hook Channel Cable Raceway review:I got the 5-pack of the large raceway figuring I could always use some spares. Besides, the cost per foot is greatly reduced compared to buying a single section. Turns out I used all but one section organizing two desks and providing a raceway between them and a printer stand. It seemed safer to use one raceway for the 110VAC cords and another for the data and low-voltage cords.The raceway works great but being a belt-and-suspenders kinda guy, I also drilled 3 mounting holes for each full section. The desks have been polished so many times I was concerned whether the adhesive could get a proper grip. The plastic is easy to cut, drill and smooth the cut edges. This is NOT light-weight crap but solid material. I'd definitely buy it again.One thing to note. The first product picture here on Amazon makes it appear the raceway has a URL printed on it. It does NOT. It is per black.

Cable channel works great.Material is easy to cut. I used a plastic miter box and coping saw to cut to length. Any small tooth saw, like a hacksaw will work.The sticky tape didn't hold too well on 3 foot run. I had to use 3 screws to attach it to underside of Ikea desk. The opening is small, but holds a lot of cables. I was able to fit 5 various laptop cables, 2 monitor cables and power supply cables with no problem.Note: Insert cables one at a time. The opening is very small but flexible.Make sure you insert least used cable in first because you might have to remove all cables to get to the one you need.

the adhesive was not strong enough to hold all the weights of the wires so i had to screw it onto the desk and not all the wires fit into the raceway, but once i got it figured out it worked like a charm.

If I hadn't chopped mine up into different pieces to suit my tables, I'd be returning them. I have some pieces with just a couple of USB/regular power cables (2-3mm think) and some with 4-5 cables running through them, mounted on the underside of different tables. They all keep coming off and falling down every couple of days since I put them up. Just standard commercial table tops - regular Velcro type strips hold just fine. Its just these that seem to have the trouble. And it is getting worse in just the one month I've had them. Today since the morning when I published this review, they've fallen off twice :( ! I suppose I could purchase some more 3m strips and give it another go, but I shouldn't have to do that. I';; probably end up taking all of them out and throwing them.I will be contacting them about a refund, but their policies don't seem very encouraging ! ([...])

I works pretty good but was very disappointing with the the tape. Mounted it to the underside of my desk, pressed three cords into it and it did a good job of cleaning things up....until the tape failed only two days after attaching it. It dropped off, taking my speakers with it to the floor. Thankfully they didn't break. Plan on getting the heavier foam 2-sided tape to make it work right.

The shape of this product allows for good grip when drawing straight lines on a dry erase board without your fingertips getting in the way of the marker. I'm adding magnetic tape on the side that points towards the floor during normal use (as shown in the product picture) so I can either stick it to the board when not in use or rotate it 90 degrees to have it magnetically stick when drawing lines. Much easier and faster to use than a normal yardstick with magnetic tape.

Well, this is a great concept but is a pretty awful product. For one, there's no practical way to get the amount of wires in that they say can fit - let alone make them stay in there. There is no lip (or at least no substantial lip) to keep the wires from slipping out of the opening. I got the small one because the measurements showed that the amount of wires that I wanted to go in there would fit no problem. Well, it was super tight, and the wires kept popping out of the place on the side where you put them in. I only bought this because it is a channel cable management system. Problem is, the channel is so poorly designed which leads to the problem I mentioned above. There is just no way to have the wires come out where ever you want them to while having them stay in the channel.

I used this behind a television located on a built in wall unit. It was placed with the tape side against the back wall, and the opening facing upward as you expect. Once it is attached the seal is perfect. The only way of getting it off is by prying with something that won't scratch the wood. I didn't think of it at the time, but using Velcro command strips instead of the tape would been the best option for removal if ever needed. It works perfectly. Every wire behind the television is neatly tucked away in the channel. All you have to do is just pull out a bit of wire at the point of connection. It even looks like it came as part of the finished cabinet.