Upgraded W10503278 Factory Certified OEM P/N WPW10503278 Jazz Control Board for Whirlpool Maytag KitchenAid Jenn-Air Amana Magic Chef Admiral Norge Roper Kenmore W10165748 12784415 67006740 8208187

Our fridge stop cooling out of nowhere despite it only being a few years old, I was able to diag it pretty quickly due to the JAZZ board being a common failure for Whirlpool. Luckily I was able to getting going again temporally while I waited for this to come in (overnight early am delivery) Pretty easy install and haven't had an issue yet (over a year) would buy again since its significantly cheaper and quick to get over OEM.

it's been working for 2.5 years so far--solved amana bottom freezer no defrost, warm top fridge issue. My fridge seems to kill these boards every 7 years even after putting fridge on a surge protector.

It was the right one for the frig, later found we really didn't need...

Installed the board two weeks ago on a Maytag Refrigerator PBF2255HEW program code 01. Fixed the problem with the top refrigerator compartment not keeping temperature and causing food to spoil. This was my last resort after checking the fans, seals and defrost (forced defrosted worked) prior to having to spend $$ on an unknow new refrigerator.

tl;dr: This fixed my fridge. It wasn't cooling, and the thermostat read "- , -".Details:I have a Whirlpool GB2FHDXWQ02 refrigerator (fridge on top, slide out drawer freezer on bottom)I came home one day and noticed the ice cream was soft.The thermostat read, "- , -". Dashes, minus signs.I tried to set the thermostat, but it did not respond to touch.The fridge was @50-60 degrees; the freezer @30. They should be 37/0.I watched a video on youtube, "Refrigerator Repair - Replacing the Electronic Control Board (Whirlpool Part # W10503278)" [you can search for "W10503278" and find a variety of videos]I disassembled my fridge. I did a wiggle test/pulled on the pcb board/wires while it was still clipped into the plastic housing. I could get the thermostat to display numbers if I held the buttons down fairly hard. I figured my jazz board was bad. (if you do this, do not touch the pcb with your fingers while the fridge is plugged in, or you will be shocked. You also risk shorting something out/damaging the fridge).I think it's a safe decision to order this board if your fridge displays dashes in the thermostat and doesn't respond to input.I ordered this part, W10503278 jazz board / control board.I broke it in half, installed it, and programmed the code.I initially thought it was broken, and not cooling.The reason I thought this, was because I set the thermostat to 7 / 7 (coldest), and the temps didn't immediately drop.I think it took 6-18 hours to really cool down. It has been @24 hours now, and my temps are 37/0, set to 5 / 5. (Which seems about right). My guess is that I'll wind up using 4 / 4.I used a Thermapen to measure liquid temperatures. I have a glass of water in the fridge. I had a glass of oil in the freezer, but it froze, and I wound up using ice cream. I also have a bluetooth sensorpush thermometer in the freezer.I think the compressor ran constantly for hours while the fridge was cooling down. I assume that's normal.I wiped up any water in the fridge/freezer, because I guess the humidity will freeze on the evaporator fins and cause problems.And I dusted out the condenser fins.I am satisfied with the repair. I hope the part will last another 10 years.In hindsight, my fridge displayed symptoms earlier. About a month ago, I think the thermostat set itself to 2 / 3 (or someone else did). And another time, I had noticed the thermostat displayed "- / -", but it responded to touch, and I adjusted it back to 4 / 4.

The Circuit Board is delivered in one piece, but the Whirlpool Refrigerator has two separate Circuit Board pieces. There was a hairline scratch on the board, maybe made by a die cutter, which corresponded to the configuration between the two circuit boards. I cut the board into two pieces using a Carpet Knife to separate the boards more, and then snap them like a ceramic tile. Then put the boards in, and programmed it., They gave programming instructiions, but no Installation instructions. I built various Heathkit Amateur Radio and Stereo kits as a kid, so know my way around Circuit Boards. Never seen anything like this, without instructions would be pretty intimidating for most people.

Funciona como el original, mi Nevera amana Funciona de nuevo