CoCsmart Flexible Car Led Light Strip, Dual Color 2 Pcs 24 Inches DRL LED Headlight Surface Strip Tube Light Daytime Running White & Amber Waterproof Switchback Sequential Lamp Turn Signal Light …

Couple of nice surprises. 1)The LEDs are facing out of the edge of strip, instead of facing up from the strip. This allows it to be installed in tight gaps, and easy to bend around corners. 2) The amber LEDs light sequentially. I would have been happy with on/off, but having them run around is a bonus. The white Leds are bright, and true white. I installed these on the outside perimeter of my RZR headlights. Some additional adhesive was needed in the tight corners, but that's to be expected.

Was very happy with the way the lights looked upon TESTING, i always test my lights when i get them. After spending hours pulling housings apart to customize them with these strips i finally get to wiring them into the vehicle. The soldering inside the control box blew a fuse and the DRL White light was inoperable. Pulled LED control box apart only top find the ground solder was held together with 1 strand of wire, the red power wire was the same way, and was stretched so far that it was making contact with the ground. EXTREMELY unhappy with the worksman ship, and now i have to take my housings back apart, use double the glue that was originally planned for, and order another set, setting me back possibly another week. EDIT: The company contacted me VIA Email and has replaced the set with a new set. Very good Customer Service as they responded only a few hours after leaving this comment, and had a new set to me within 2 days. Changing my review to 5/5, the company acknowledged they sent me a faulty part, apologized, and sent me a new part fast. Will order from them again in the future

One side won't light up white. Adhesive is weak. Waiting to hear back from them regarding the o e light, glad I didn't remove the headlights first without testing. 🚨UPDATE 3/21/21🚨 The product was exchanged. Again, I tested out of the box, this time they work 👍 I'm hoping these are long lasting. I spent time on this install. I used Gorilla Glue to adhere the light strips. All in all, I got them to look OEM. My only complaint is they are not really that bright during the day. Also, as a turn signal the sequential amber works, with no other lights on. If I turn on these strips with the parking lights, no amber works. That is fine with me, if it's not a wiring issue that I will checkout tomorrow. If you take your time to install these correctly, I think you be satisfied. If you just want to slap them on out of the box, the very MINIMUM I would do is at least use good 3M double sided tape

I purchased one set of these lights strips with hopes they would turn out looking nice, if they did I was planning to purchase a second set. Unfortunately the set I received had poor and brittle connections to the led strips. Before installation just moving the strips around caused the wires to break apart from the very small soldering connections. I wish I could have these set up as well as a second pair but unfortunately I must've received a defective or poorly made pair. The actual hardware used to construct these seem to be high quality actually I'm surprised the soldering connections didn't hold up. Thank you for reading and I hope I can get this figured out.

Coming back to this 2 years later, and I must say these have been awesome to drive with! So honestly only one led bulb has gone out on both sides in the same place and only in blue. Not bad for two years! I will buy again when the weather warms up for it is easier to install when warm. Also I bought a role of 3m tape to apply these with, because the adhesive isn't the best that comes with them. Overall I highly recommend these rgb+turn led strips.

The wires connected to the device are short and fragile. You have to extend them anyway because they are too short and to get the opposite side turn signal wire you have to span the front of your vehicle with extra wire. You will need to solder also. You will also need to know a little about automotive wiring to find where your connections need to be because no instructions. Because they are so dim you need to get them right to the edge of your headlight or they will never be seen, even at night. I thought I could place them further back over the headlight and just see the glow of the lights when they were working. Nope, too dim. So I moved them to the front edge of the light just under the edge of the hood. If I find something brighter these are being removed.

Good look ....couldn't finish the install. 3 LEDs out on the first power test...these are very fragile.. ***UPDATE***... new set all is well. These can be a great mod to your car if you take the time and do the install to survive elements if you are mounting this outside of the headlight. 1. Test - should be the first thing you do. confirm look and color. 2. have on hand. a. better 2 sided tape. b. liquid tape c. Silicon RTV/Superglue/Gorrilla Glue d. Goo Gone 3. handle these like crystal they are fragile!!!!! 4 seal control box openings with liquid tape, build up a few layers. (after cutting I reused end caps.. added silicon and pressed it on to ends this takes a while to dry and cure. 5. use goo gone to help remove installed 2 sided tape (be careful of ends. 6. this also allows you to use both sides of the lights. I chose to point LEDs into the headlight bucket. the leading edge is still bright but not as good as led pointing out... test fit both ways to be sure. 7. GIVE LIGHTS TIME TO DRY.. and they should last a good while.(a single drop of water and these are toast) 8 done right the prep should take you 24 hrs including drying time to be safe

Quality product work great fast shipping thanks

zuper

ممتاز

No hace la función que anuncian el los videos cortod

المنتج ليس كما بالوصف الديكودر غير موجود

واحد من الاضائات اللحام بتاعها كان فاكك بس عرفت افكها والحمها لكن طبعا الحوار دا مش اي حد هيعرف يعمله او هيكون معاه الادوات لكدا, بس عموما جميلة وضائتها كويسة.