Danco HYR451T HyrdroRight Universal Water-Saving Toilet Repair Kit with Dual Flush Valve, Lever Handle, White, HYR451T

Everything about this works great, just one detail to pick on. Where it goes into the big hole, very much wish there was a long cylindrical rubberized tube. Item is so light it had to be engineered to stay in place. Otherwise, very quiet, flushes extremely well, and very easy to use. Very sorry I bought a Home Depot, this really was that much better.

11/21/14 Updated to 4 stars: Okay so now it works fine. I ended up having to replacing the flush valve to obtain a proper seal after the flush. Apparently I had a better seal with the old flapper and flush valve but it still ran so it needed to be changed, which is what started this conversion. Now I just need to figure out how to adjust it properly. The partial flush doesn't flush a square of paper at this point but the full flush works fine. Eventually I hope to have it adjusted properly. End result after all is pretty good. I guess I will have to see how it holds up over time. Happy with it now! Right now I am not happy!!! I have installed and re-installed 3 times. I read the instructions a few times before installing and watched several videos. I have installed many of the typical setups in toilets before. The installation was easy, no problem each time I tried it was quicker and everything seemed to be great each time until I let the water into the tank. The tank fills properly, but once full the water continually drains from the tank causing the refill to go on every few seconds no matter how many times i take it apart and re-seat it. I guess i am just totally frustrated at this point and wanting to put all the old parts back on. I only changed them thinking I would save water. After all, we are in a drought here in California so anyway to save water waste is good in my book. So my next move I guess is to go to the hardware store and try to find all the rest of the internal parts to replace. I guess i need to get a new overflow tube and flush valve assembly and then try to re-install again with a completely empty tank and all new parts. I'm also thinking since this is a kit the flush valve and overflow tube should be part of it or the first instruction should be: Go buy all new parts first so you won't become frustrated after trying to install. My opinion only! Am I the only one with this issue? If anyone has any hints I am open to them. I don't feel i am installing incorrectly but then again I'm not a plummer and just following instructions. When I try again, if it works I will come back and update. I was really hoping this would have been a 15 minute to 1 hour job and not a few days. :(

Have now had installed for 6 months in one case and 2 months in two others. Working just fine. One advantage to these systems is the white slide mechanism on the filler tube. You can slide that so that it will not refill after flushing. This is a big help if have to adjust the replacement for the flapper value but even bigger help when wanting to clean the toilet bowl. Can slide to stop flow, flush using the liquids flush button and then with the bowl nearly empty can clean the bowl thoroughly. Then release the slide and bowl refills normally. Big help vs turning the water off at the valve. Same is true if going on vacation or away for weekend and want to prevent possible toilet overflow as mentioned below. Features not mentioned in other reviews I have seen on the product but a big plus for it. This us update to earlier note. I have now installed three of these systems. The only issue I had was getting the flapper replacement installed so it did not leak. But once that problem was solved the system works great. One item I have not seen noted but important to me is that you can slide a white slide on the arm of the filler mechanism to lock it in place. Very useful if going on vacation or even away for weekend as it could prevent a toilet from overflowing as friends had happen a few years ago with major damage. Beats turning water off to the whole house as the major risk is from the toilets. System worth it just for this! Also when checking for leak you can mark level with pencil and lock the filler and then go back in a few hours and see if level has dropped. Likewise if you have to adjust the flapper replacement it is easy to do by locking the filler when water level is low and then twisting the large part off of the flapper replacement and adjusting to be sure no leak. After doing this can release to let water part way in and then lock again and mark so do not have to fill entire tank (or drain it). Thought these useful enough to pass along. I initially bought each of these separately so my review of the filler valve and the dual flush valve are under the individual parts except that I am only adding the comments above to the entire system link. I have replaced the innards of toilets numerous times over the years and found this system very easy to install. Only caution I would pass along is to read the directions and the warnings with some care before you attempt installation. I have for years used bleach tablets in the tanks and I note that they warn not to do this with their system. Each part of the installation has some simple instructions but important to read them to save yourself a lot of frustration. When I first installed the dual flush I did not follow instructions to put water over the seating valve and mark with pencil and let sit 15 minutes to be sure it was seated. As a result I had to go back and redo the installation. Once you have done an installation for one toilet doing others will be extremely easy. So far system is working very well but I plan to wait a couple of months before buying more and installing in my other toilets. If this works as well as I hope I will be using these from now on. Especially attractive to me is replacement of flapper valve and those of us with hard water tend to find build up of sediment and lime allows leaking of the flapper over time which can waste a great deal of water from a very slow leak that you may not realize is occurring. If I find problems with the units after installed a while I will come back and revise this review. As of now I can recommend this unit both for ease of installation and how well they are operating so far. Some of the problems I have seen in other reviews have yet to show up for me. If they do I will edit this review.

I have no idea what is the difference with the HYR270 aside from the flash switch. Very difficult to setup. I tried many times but there is always a leak since the rubber fit does not fit properly. I actually have to glue the rubber to the receiving hole. And made hude customize just to properly align and stabilize the device attaching to the tube. I glued it as well to make it steady.

Es un excelente producto. Funciona tal cual está indicado. En mi caso, el sapo de la descarga se atoraba y no regresaba a tapar la descarga, lo cual generaba una fuga de agua muy considerable y por lo mismo, un consumo de agua mayor (+ $$$$ pagada al servicio municipal de agua potable y alcantarillado). Se puede instalar en cualquier depósito, no se requiere que sea nuevo o que este preparado para este tipo de válvulas. Este es el 2do juego de baño que instalo. En ambos casos la instalación fue super sencilla y no requerí herramienta (solo para quitar la manguera de la tubería al deposito). En la 1er instalación me lleve aproximadamente 45 minutos. Ya en esta última fueron máximo 15 minutos. Los materiales de primera calidad y no se requiere desensamblar el tanque al inodoro pues ocupa la misma descarga. Recomiendo que lean bien las instrucciones de instalación y se familiaricen con las piezas. Si he observado una disminución del consumo de agua a raíz de la instalación y uso de este sistema. Inclusive hasta la sensación de desperdiciar agua de mas en cada descarga se ve reducida.

Makes my ordinary toilet from 1988 like a complete new toilet dual flusher for $170 available at the hardware store now. This kit is not available in Calgary Canada hardware stores in January 2015. Maybe after a big mark-up next year. Fit great and works ░▒▓█▀▄▀ ◆ A ◆ W ◆ E ◆ S ◆ O ◆ M ◆ E ◆ ▄▀▄█▓▒░. Says no tools needed but what about the removal of the old hardware? Someone didn't think outside their box on that one. LOL Instructions show a picture of old hardware with an arrow caption that says "Remove old toilet fill valve". Just a pair of channel locks and a pair of scissors and you're all set. Make sure the inlet float valve is adjusted for the very top of your tank lid or will not operate properly. I was just half an inch too low and it bunged up. Can not adjust after you tighten it up so this is step one and the most important step. Other wise you dump more water on the floor on your second attempt. This is allowed for but don't over tighten because breaking the plastic nut auto adjustment tabs might just make the second attempt more difficult. These tabs are designed to break off if you over Solomon Grundy them. Adjustments for small flushes takes a little experimentation. All parts are made of 100% real plastic. Don't settle for less, buy authentic genuine plastic.

Easy to install, low flush won’t work without holding the Handel. The full flush works perfectly. Did all the adjustment on bleue tab and green tab, nothing will make small flush works unless holding 3 to 4 seconds.

Substituye todo el herraje interno y funciona bien modernizando y actualizando el funcionamiento del inodoro, ahorra agua , evita fugaz al ser más exacto en el uso del agua .