RealTruckBAK BAKFlip MX4 Hard Folding Truck Bed Tonneau Cover | 448339 | Fits 2021-2025 Ford F-150 (incl. Raptor/Lightning) 5' 7" Bed (67.1")

Just installed it today and drove around for a few hours. Really good fit. Installation took me about 45 minutes. Very straight forward. Materials are all high quality. Finish is good. It either made it quieter or it quieted some of the frequencies that are most obnoxious. It rolls up tight and compact. It doesn't have a lock but when the tail gate is locked you can't open it. I think a real dedicated thief could get through, but it will stop those looking for just an easy target. Overall super happy.

Great so far. We took our time and installed the tonneau in about 40 minutes. Looks great. The other comments about some aluminum filings were certainly true. I just used my air compressor and blew them off. There was a bit of a sharp edge on the leading edge of the aluminum channel at the lift gate that I filed down just so I would not accidentally cut myself. Hope the manufacturer reads this, it would be very simple to file this during manufacturing.

Easy to install. Gets the job done & looks terrific. Flush fit is sleek and reasonably tight: Now for the bad. The product weighs substantially less than prior versions which I have purchased in the past for F150 Ford pick ups. They have worked a lot of manufacturing cost out of the product and in my opinion, sacrificed some durability along the way. Don’t think for a moment that you’re going to stand on top of this thing like you could with the past versions despite what some people say. If you value your life, don’t do it. However, because the panels physically weigh less they’re certainly easier to open and close. How much less? No I didn’t take the time to put them on a scale, but rest assured, they are dramatically lighter weight than the original. Keeps the water out of the bed for the most part. Overall, I still think it’s a good product, but I knocked off one star for clearly what they’re doing to the long-term durability of the bed cover.

Super easy install, unfortunately came with no instructions but customer service at real truck emailed me them and an install video with no issues. Highly recommend, super light and sturdy. I had the ford factory branded one before which I was told was the same one. This is the newer model and was $400 cheaper that the ford one. Install took about 30 min and I did it by myself

Hi,I just wanted to share some feedback on the MX4 cover I installed on my truck. I’m extremely satisfied with the product—it looks great, fits perfectly, and feels very solid. The installation was straightforward, and I really appreciate the quality of the materials and design.It not only adds a sleek appearance to the truck but also gives me peace of mind knowing my cargo is secure and protected from the weather.Excellent product—I highly recommend it!Best regards,

There were no instructions in the box, I found a sheet with a QR code that would take me to their website trying to sell more of their gear. I had to navigate to find instructions for other trucks not mine. I found videos on youtube, but all were for a different cover with the same model which didn't have the same setup.The picture on the one I ordered is grey, mine arrived in black. The clip for the arm to hold up the cover popped off and broke easily as I tried to place back on to the unit.

To set the stage for why this cover is so great... I previously had a different tonnaeu cover that was a folding one that had 4 panels / 3 folds. To fold it back required me to undo two clamps at the back, secure the clamps, fold it two times, unclamp two clamps at the middle on each side of the truck (requiring me to go around the truck or have a second set of hands), and then fold again... it was a pain in the butt, and the rear clamps would often disengage at the slightest brush or bump so it wasn't uncommon to see a corner flapping in the wind. My girlfriend absolutely hated the old cover, particularly whenever we'd require folding it to get at stuff that was shifted to the front side of the bed.So I bit the bullet for the Revolver X4s, a bit pricier than I wanted to spend but I'd seen another truck owner with the similar X2 and I decided it was the cover I wanted as it hit all the checkmarks.It's exactly as advertised. It's solid, and I feel it's more secure and secures my stuff in my truck bed better than the old vinyl cover. It's easy, I can open and close it entirely myself with one hand, and it makes it so much easier to access the full contents of the truck bed. It's beautiful and goes very well with the truck. I definitely would recommend to anyone else looking for a cover.

Super easy to install, need to look up the instructions online on youtube. QR code is provided in packaging.Feels significantly lighter than the stock trifold tonneau, but still feels solid. Install took about 90 minutes including removing the old tonneau and cleaning the sides of the truck bed.